background image

I.  INTRODUCTION 
 

Before you begin installation of this fireplace, read these instructions completely. 

 

This fireplace and its components are safe when installed according to the installation manual. 

 

Unless Southwest Firebird Manufacturing/KIVA parts are used, which have been tested and approved for this  

 

fireplace, a firehazard may result. 

 

The Southwest Firebird Manufacturing/KIVA warranty will be voided and Southwest Firebird, Inc. disclaims any       
responsibility for the following infractions: 

1.  Any modification of the fireplace, components, doors, air inlet system, or damper control. 
2.  Use of any part not manufactured/approved  by Southwest Firebird Manufacturing Inc. 

 

PROPER PREPARATION prior to fireplace installation is very important to ensure  
safety and continuous operation. Consult the local building codes for specific 
requirements for your area. 

SELECTING A LOCATION 

To determine the safest and most efficient location for the fireplace the following guidelines must be taken into considera-
tion. 

1.  The location must allow for proper clearances

 

(See Pages 5 & 7). 

2.  The location of the fireplace should not be affected by drafts, air conditioning ducts, windows or doors. 
3.  A location where the cutting of joists, or roof rafters can be avoided. 
4.  The required outside air kit can be easily installed

 

(See Page 6).     

 

II.  FIREBOX INSTALLATION 

 

 

When installing the firebox, it must be placed on a level non-combustible surface.  If the existing floor surface is wood, vinyl 
or any combustible material, the flooring needs to be protected with ½” x 4’6”x 4’6” masonry board to the full dimension of 
the frame/cage (if used).  A minimum of 18” clearance from the firebox opening to any combustible is required.    

FOR YOUR SAFETY 

 

Do not store or use gasoline in the vicinity of this or any other appliance. 

 

Due  to  high  temperatures,  the  appliance  should  be  located  out  of  traffic  and away 
from furniture and draperies. 

 

Do not place clothing or other flammable materials on or near the appliance. 

 

NEVER leave children unattended when a fire is burning in the fireplace 

 

CHECK LOCAL CODES BEFORE INSTALLING THIS FIREPLACE. 

 

This wood burning fireplace complies with UL 127 standard as a FACTORY BUILT FIREPLACE. 

Warning this fireplace has not been tested with an unvented gas log set. To reduce risk of fire or injury, do 
not install an unvented gas log into fireplace 

 

 

WARNING

:  Do  not  install  fireplace  insert  in  this  firebox  unless  the  manufacturers  instructions  with  the  insert 

specifically state the Southwest Kiva fireplace has been tested for the insert. 

Summary of Contents for Kiva SWK24
















Reviews: