AR-323-D
V200623
ACCESS & INDUSTRIAL CONTROL
- 2 -
Smart Digital Door Lock
RF Card
1
2 3
4
5 6
7
8
0 #
*
9
Z
Z
Y
X
Z
A
B
B
C
A
A
B
B
C
C
D
Handle hole
Deadbolt knob hole
Cylinder hole
Cable hole
9.Elastic Spring
10.Allen Wrench
X CN1
Y CN2
Z CN3
5.Cylinder Lock
6.Mechanical Key
7. Waterproof Strap
8.Handle Screw
1.Mortise
2.Mortise Plate (mounted)
3.Spindle of Knob
4.Spindle of Handle
5.
1.
(1)
(1)
4.
3.
2.
(2)
7.
(7)
8.
8.
9.
9.
7.
6.
10.
Cross-Head screw driver
Tools
16.
17.
18.
STEP 1 : Stand-alone: Install battery before the upper
cover of back panel.
STEP 2 :Install the lower cover of back panel as above
picture shown.
Using (10) Allen Wrench, Fasten the (8)Handle Screw into
(E)Handle Screw Hole up until it reached Front Panel and
properly fasten.
※
Note: Before tightening the screw, make sure the
Waterproof Strap is fit in the Back and Front
Panel, Back Panel and Front Panel position is in
correct position
1. Peel off “Strike Sticker” and paste into the desired
spot for installation
2. Start making the hole drilling based on the hole
dimension on the sticker
3. Remove the sticker after hole drilling is finished
STEP 1 : Embed the Strike Box into the hole
STEP 2 : Embed the Strike Plate on Strike Box and
fasten with Screws
STEP 3 : Installation of Strike is finished.
1.
2.
3.
1
1
5.87
20*10
11
5.87
20*10
115
.8
7
20*10
Paste hole-sticker on the door properly and
make cuts depending on hole-stickers
dimension.
Install cylinder into mortise , use the screw to
fix cylinder properly
Fasten (5) Cylinder Lock into hole
Place back (2) Mortise Plate into
Mortise lock body (original position)
Remove (2) Mortise Plate from (1) Mortise
lock body
Embed (1) Mortise into the hole
Insert two of the (4) Spindle of Handle into
hole
Installation front and back panel.
Strike components installation and
fasten Screws
Waterproof strap and fixing screw
Waterproof Strap
Strike hole drilling
※
Note :
1
.
Only make "deadbolt knob hole" from inner door to
mortise, don't cross to outer door.
2
.
Make sure accurate position & right hole direction of
striker plate; before making cuts, latch bolt position can
be made firstly.
3
.
Networking mode : Additional hinge cuts is required for
PC connection.
STEP 1 : Insert the (1)
Mortise into the hole.
STEP 2 : There is a CN3 cable connecting (1) Mortise with
Front Panel, make sure the cable is out from hole.
STEP 3 : Next, make sure that the external power and
communication cable to CN1 is ready and wired on site
Separate (2)
Mortise Plate from (1) Mortise lock by
unfasten the screw that has already mounted. It is
because the first step to be done is to fasten Screws
between (1) Mortise and door and mounted (2)
Mortise Plate is closing the path of it.
1
1
5.87
20*10
4.
8.
9.
5.
6.
7.
12.
※
Important:
1. The depth of the (5) Cylinder Lock installation has
already fixed. The screw position must meet with the
hollow part of the (5) Cylinder Lock
2.
We suggest making sure that the upper bolt and the
lower bolt functions correctly before fixing the screw.
Testing can be made using the mechanical key by
rotating it to left and right and it will move bolt position
means it works properly.
1. Make sure the key lock hole on the topside,and fixed
tightly.
2. Please confirm the key can control 2 bolt.
Fasten the (1) Mortise lock into the door
with Screws on both side
※
Note: The crooked part is in the Back Panel position,
and the flat surface is in “ 1 ”Mortise position.
※
Note: The crooked part is in the hole position, and the
flat surface is facing out.
Provided (7) Waterproof Strap is recommended to apply
for waterproof function and to preserve the lock durability
from door opening and closing
STEP 1: Provided (7) Waterproof Strap is recommended to
apply for waterproof function and to preserve the
lock durability from door opening and closing
STEP 2: Put in (9)Elastic Spring into (8)Handle Screw (this
is optional but suggested for durability purpose)
STEP 1
STEP 1
STEP 2
STEP 2
STEP 2
E
E
E
D
F
G
Handle screw hole
Mortise hole
Strike hole
4.
14.
STEP 1 : Disassemble the upper cover (sliding type)
STEP 2 : Disassemble the lower cover (buckle type)
Disassemble Back Panel cover
STEP 1
STEP 2
Fix Front and Back Panel position
15.
1
2 3
4
5 6
7
8
0 #
*
9
Front panel
Back panel
Connect (1) Mortise to Front Panel
10.
STEP 1 : Connect the Front Panel CN3 Connector of
Mortise to (1) Mortise
STEP 2 : Bring CN2 Connector of Reader into Cable
Hole to be connected to Back Panel later
STEP 3 : Plug in (4) Spindle of Handle on the mortise into
Handle Hole
Front panel
STEP 1
STEP 2
STEP 3
Connector
of mortise
CN3
CN3
STEP 1
STEP 3
STEP 2
D
D
D
D
A
C
A
C
(5)
(2)
(4)
(4)
PART 1: MORTISE
Z
CN1
X
CN2
Y
CN2
Y
(1)
(1)
(4)
Connect (1) Mortise to Back Panel
13.
STEP 1 : Connect the CN1 Power and Communication
Cable to DC power and RS485 communication
(refer to the ‘Wiring’ Section)
STEP 2 : Continuation from Step 10-2 connect the cable
from Cable Hole to CN2 Connector of Reader
of the Back Panel
STEP 3 : Fasten (3) Spindle of Knob from Deadbolt Knob
Hole of (1) Mortise into Deadbolt Knob Hole of
the Back Panel
1
2 3
4
5 6
7
8
0 #
*
9
CN1
CN2
STEP 3
STEP 2
STEP 1
D
B
B
B
(3)
CN3 CN2
PART 2: HANDLE PANEL(Front Panel)
PART 3: STRIKE
Front Panel
Back Panel
11.
Cover Cylinder Lock by sliding up the the lower cover and
finish installation
Place the lower cover for the Front Panel
STEP 3
1
2 3
4
5 6
7
8
0 #
*
9
PART 3: HANDLE PANEL(Back Panel)
(7)
(8)
(9)
(8)
(9)
Back panel
A
