background image

ii 

 

Rev 004, 07/11 

 

 

© SP Scientific 2011 

Important Symbols 

 

 

 

WARNING! INJURY OR EVEN 
DEATH MAY RESULT IF A 
RECOMMENDATION MARKED 
WITH THIS SYMBOL IS NOT 
HEEDED. 

 

CRUSH HAZARD. KEEP HANDS 
CLEAR WHEN OPERATING DOOR. 

 

ELECTRIC SHOCK DANGER! 
USE APPROPRIATE CAUTION 
TO AVOID INJURY OR DEATH. 

 

CORROSIVE CHEMICAL. WEAR 
SUITABLE GLOVES, SAFETY 
GLASSES, AND PROTECTIVE 
CLOTHING. 

 

BURN DANGER! POTENTIALLY 
HOT SURFACE. USE 
APPROPRIATE CAUTION.  

  

 

PROPERTY CAUTION! TO PREVENT 
DAMAGE TO CHAMBER EQUIP-
MENT AND/OR LOAD, ADHERE TO 
PROCEDURES MARKED BY THIS 
SYMBOL.   

 

DO NOT STORE FLAMMABLE 
MATERIALS IN CHAMBER. 

 

PRACTICAL OPERATING TIP. 
THESE RECOMMENDATIONS 
STREAMLINE UNIT OPERATION 
AND PREVENT COMMON 
OPERATOR ERRORS. 

 

WEAR SAFETY GLASSES. 

 

EXPLOSIVE MATERIALS HAZARD!  
KEEP OBJECTS AWAY FROM HEAT. 

 
 
 
 

Safety Warnings 

 

Always transport the unit with care. Sudden jolts or drops may damage the refrigeration system. 

 

Always observe all warning labels. 

 

Always turn off the unit and disconnect the line cord from the available power source prior to performing any 

service or maintenance procedures. 

 

Always turn off the unit and disconnect the line cord from the available power source prior to moving the unit. 

 

Always empty the reservoir / bath chamber prior to moving the unit. 

 

Never operate equipment with damaged line cords. 

 

Never operate the unit without cooling fluid in the reservoir / bath chamber. 

 

Never remove warning labels. 

 

Never operate damaged or leaking equipment. 

 
 

 

 

Summary of Contents for FTS SYSTEMS AD80 & AF6





















Reviews: