background image

Rev 002, 04/11 

 

iii 

© SP Scientific 2011 

Warranty Information  

FTS Systems Lyo-SEA for VirTis Genesis  is  warranted by SP Scientific to be free of defects in material and 
workmanship when operated under normal conditions as specified in the instructions provided in this manual. Please 
take this opportunity to locate the serial tag on your new FTS Systems Lyo-SEA for VirTis Genesis  and record the 
information below for future reference. SP Scientific also recommends that you complete and return your unit’s 
warranty registration card. 

 
Model Number 

 

 

 
Serial Number 

 

 

 
Part Number 

 

 

 

 

 

Limited Warranty 

 

SP Scientific (the “Company”) shall warrant each of its products against defects in material or workmanship for a period 
of 12 months from the date of installation or 15 months from the date of shipment (whichever comes first) provided that 
the product is used in a reasonable manner under appropriate conditions and consistent with the applicable operating 
instructions. 

 

The obligation of the Company shall be, at its option, to repair or replace, without charge any parts that prove to be 
defective within the warranty period, if the purchaser notifies the Company promptly in writing of such defect. No 
product shall be returned to the Company without prior approval of the Company. 

This limited warranty shall cover the costs of parts and labor to repair or replace all defective product(s) at the Seller’s 
factory. For all products installed by the Company and located within the Company service travel areas, this warranty 
shall cover transportation charges to ship the product to and from the Company’s factory and/or the costs of travel, 
room and board if the Company’s employees conduct repair at the Buyer’s location. In lieu of repair or replacement at 
the Company’s factory, the Company may, in its discretion, authorize a third party to perform the repair or replacement 
at the Buyer’s location, and at the Company’s sole expense.  

The Company shall not be responsible for labor charges payable with respect to persons other than Company 
employees. Replacement or repair of parts pursuant to this warranty shall not in any way extend the original warranty 
period. The Company shall not be responsible for any unauthorized repairs, replacements or product modifications, nor 
will it be responsible for any product failures resulting from such unauthorized repairs, replacements or product 
modifications negligently or otherwise made by persons other than Company employees or authorized representatives 
of the Company. The buyer shall assume transportation charges to ship the product to and from the Company’s factory 
and the costs of travel, room and board if the Company’s employees conduct repair at the Buyer’s location within the 
warranty period if the product was not installed by the Company’s and/or is not located within the Company’s service 
travel areas. 

THE COMPANY DOES NOT MAKE AND EXPRESSLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WITH 
RESPECT TO THE SALE, INSTALLATION, DESIGN OR USE OF ITS PRODUCTS. ADDITIONALLY, THE 
COMPANY SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF OR 
ANY DEFECTS IN ITS PRODUCTS. 

The Company’s employees are available to provide general advice to customers concerning the use of the Company’s 
products; however, oral representations are not warranties with respect to particular products or their uses and may not 
be relied upon if they are inconsistent with the relevant product specifications for the items set forth herein. 

Notwithstanding the above, the terms and conditions set forth in the Company’s formal sales contracts shall be 
controlling and supersede any inconsistent terms contained herein, and any changes to such contracts must be made 
in writing and signed by an authorized executive of the Company. 

 

 

 

 

WARNING! THE DISPOSAL AND/OR EMISSION OF SUBSTANCES USED IN 
CONNECTION WITH THIS EQUIPMENT MAY BE GOVERNED BY VARIOUS FEDERAL, 
STATE OR LOCAL REGULATIONS. ALL USERS OF THIS EQUIPMENT ARE URGED TO 
BECOME FAMILIAR WITH ANY REGULATIONS THAT APPLY IN THE USERS AREA 
CONCERNING THE DUMPING OF WASTE MATERIALS IN OR UPON WATER, LAND OR 
AIR AND TO COMPLY WITH SUCH REGULATIONS. 

 
 
 

Summary of Contents for FTS SYSTEMS LYO-SEA





















Reviews: