SP Jetwash SP250P Operator'S Manual Download

Page: 14 / 17

ENGINE TROUBLE SHOOTING GUIDE

When the engine will not start:

DRAIN SCREW

YES

Is there fuel in
the tank?

Refill the fuel tank

Is there oil in the
engine?

Is there a spark
from the spark
plug?

Add the recommended
oil.

Replace the
Spark plug.

Take the engine to
an

authorised

service dealer.

Be sure

there is no spilled fuel
around the spark plug.
Spilled fuel may ignite.

To check:

1)Remove the spark plug

cap and clean any dirt from

around the spark plug.

2)Remove the spark plug and

install the spark plug in the plug

cap.

3)Set the plug side electrode on

the cylinder head.

Is the fuel reaching
the carburetor?

Clean the fuel
sediment cup

If the engine still does
not

start,

take

the

engine to an authorised
service dealer.

To check:

)Turn off the engine switch and

loosen the drain screw.

2)Fuel should flow from the drain

when the fuel tap is turned on.

Still no spark

YES

Summary of Contents for Jetwash SP250P


















Search results

Summary of Contents for Jetwash SP250P

Reviews:

Related manuals for Jetwash SP250P

Brands by name

Popular brands

SP Jetwash SP250P, Operator'S Manual

Search results

Summary of Contents for Jetwash SP250P

Reviews:

Related manuals for Jetwash SP250P

Brands by name

Popular brands