Spa Builders AP-4 SYSTEM Owner'S Operation Manual Download

Page: 8 / 17

ELECTRICAL REQUIREMENTS

220 Volt

50 Amp Service

Phase

2 wire- L1, L2 & Ground – Dedicated 220V unit only

(3 Wire- L1, L2, Neutral & Ground - Utilizes 220V and 110Vac components)

No.

6 AWG

supply wire is required

No.

8 AWG

conductor is required for bonding

USE COPPER CONDUCTORS ONLY

110 Volt
20 Amp Service

60 Hz
1 Phase
2 wire- L1, Neutral, & Ground

No. 12 AWG

supply wire is required

No. 8 AWG

conductor is required for bonding

USE COPPER CONDUCTORS ONLY

It is the responsibility for the installer and the owner to install a
readily accessible disconnecting means during the installation.

MOUNTING

Per UL 1563, paragraph 6.4.3, the AP-4 Indoor Spa Pack and the additional pump
(Jets 2, optional) shall be mounted so that the lowest portion of any live part is a
minimum of 4 in. above the mounting surface.

CAUTION: THE EQUIPMENT AND CONTROLS SHALL BE LOCATED
NOT LESS THAN 5 ft (1.5M) HORIZONTALLY FROM SPA OR HOT
TUB.

ELECTRICAL RE

UIREMENTS

Summary of Contents for AP-4 SYSTEM


















Search results

Summary of Contents for AP-4 SYSTEM

Reviews:

Related manuals for AP-4 SYSTEM

Brands by name

Popular brands

Spa Builders AP-4 SYSTEM, Owner'S Operation Manual

Search results

Summary of Contents for AP-4 SYSTEM

Reviews:

Related manuals for AP-4 SYSTEM

Brands by name

Popular brands