QUICK CARD - USER GUIDE FOR THE
QUICK CARD - USER GUIDE FOR THE
QUICK CARD - USER GUIDE FOR THE
QUICK CARD - USER GUIDE FOR THE
QUICK CARD - USER GUIDE FOR THE
SP
SP
SP
SP
SPA PO
A PO
A PO
A PO
A POWER 1000 SERIES
WER 1000 SERIES
WER 1000 SERIES
WER 1000 SERIES
WER 1000 SERIES
SP
SP
SP
SP
SPA CONTROLLERS
A CONTROLLERS
A CONTROLLERS
A CONTROLLERS
A CONTROLLERS
Dealer Stamp:
QuickSpaPwr1000-2speed-EMC, NRC
Please read these instructions carefully
Miscellaneous:
The switch normally beeps every time a button is pushed. These
can be switched off by holding down the up button and simultan-
eously pushing the light button. To switch on again repeat the
above.
The display normally always returns to the pool temperature. If
you want the display to stay on time, then pushing the display
button until time is shown and pressing the down button will lock
the display in this mode. The temp display can be restored at any
time by pushing the display button.
In the event of electrical interference this unit automatically resets
to a pre-determined safe state.
Error codes :
01 - Stuck button
02 - No controller data
03 - Temperature sensor
04 - Water sensor
05 - Pool over temperature
06 - Heater thermal cutout
07 - Stuck heater relay
08 - Not used
09 - Water prime failed
Heating Indicator:
& Load Shedding
This indicator shows when the pool is being heated. It
will turn on and off automatically in auto and manual
modes when heating is required.
Load Shedding
(keeping power within design limits) is an arrangement predefined
at manufacture which, dependent on system and components
used, will switch the heating element off to keep within the
controller’s power limits.
Manufactured By:
Spa-Quip Ltd
Cnr Rothwell Ave & Albany Hwy
North Harbour Industrial Park
Auckland, New Zealand
Ph (649) 415 8622, Fax (649) 415 8621
Email: service@spa-quip.co.nz
Australian Distribution and Service:
Spa-Quip (Australia) Pty Ltd
Unit 2A, 4 Hudson Ave
Castle Hill NSW 2154
Ph (612) 9634 5600, Fax (612) 9634 5900
Email: service@spa-quip.com.au
Web site: http://www.spa-quip.co.nz
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
12345678901234567890123456789012123456789012345678901234567
Warning:
If the supply cord is damaged, it shall be
replaced by the manufacturer or its service
agent or similarly qualified person in order
to avoid hazard.
N376
spaparts.com.au - Australian Spa Parts
