QUICK CARD USER GUIDE
SPA POWER 2000
SPA CONTROLLERS
Dealer Stamp:
QuickSpaPwr2000
Please read these instructions carefully
Miscellaneous:
Important: Before using check that the Spa Pool has been
connected to a suitable weather protected outlet socket and
double pole isolating switch with ratings as specified on the name
plate of the control box. Do not run this appliance on an
extension lead.
LCD brightness (contrast) can be adjusted by holding down the
Display button and the Up or Down button. To lighten the display
hold down the Display button and the Up button. To darken the
display hold down the Display button and the Down button.
The control panel normally beeps every time a button is pushed.
These beeps can be switched off by holding down the Up button
and simultaneously pushing the Light button. To switch the beeps
on again repeat the above.
The display normally automatically returns to displaying the pool
temperature. The display can be made to stay on time by first
pushing the Display button until time is shown and then pressing
the Down button. The temperature display can be restored at any
time by pushing the Display button.
For accurate temperature readings it is advisable to run the pump
for several minutes in Manual mode to mix up the pool water.
In the event of electrical interference this unit automatically resets
to a pre-determined safe state.
Error codes :
01 - Stuck button
02 - No controller data
03 - Temperature sensor
04 - Water sensor
05 - Pool over temperature
06 - Heater thermal cutout
07 - Stuck heater relay
08 - Not used
09 - Water prime failed
Spa-Quip (Australia) Pty Ltd
Unit 2A, 4 Hudson Ave
Castle Hill NSW 2154
Ph (612) 9634 5600, Fax (612) 9634 5900
Email: service@spa-quip.com.au
Web site: http://www.spa-quip.com.au
Manufactured By: Spa-Quip Ltd
Cnr Rothwell Ave & Albany Hwy
North Harbour Industrial Park
Auckland, New Zealand
Ph (649) 415 8622, Fax (649) 415 8621
Email: service@spa-quip.co.nz
Web site: http://www.spa-quip.co.nz
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
1234567890123456789012345678901212345678901234567890123456
Warning:
If the unit is fitted with a supply cord and it
gets damaged, the unit must be returned to
the manufacturer or approved service agent
or similarly qualified person to be repaired.
spaparts.com.au - Australian Spa Parts
