background image

Page 18

Specifications

*

:

Body

Stainless Steel

Power Rating

220V/50Hz or 120V/60Hz (USA & Canada standard)

General Input Power

190 W (120W + 2x35W)

Motor Input Power

120 W

Motor Revolution

800 RPM (±10%) to 1300 RPM (±10%)

Levels Of Speed Control

4 or 6 Levels

Maximum Airflow

860 CFM

Air Pressure

150 Pa (200 Pa Maximum)

Noise Level (dB / sone)

Approximately 35 / 0.7 to 67 / 6.5 (Lowest to Highest Speed)

Motor Type

Single Chamber Ultra Quiet

Fan Type

Centrifugal / Sirocco

Control Type

4 or 6 Speed Electronic Touch Sensitive

Filtration Type

Stainless Steel Baffle Filter

Illumination

Halogen 35W or LED 3W Type GU10 120V (220V for Europe) 

Venting Size

Top, 6 Inches Round

Interference Protection

Radio Frequency Interference Protected

Specifications

Use and Care Information

Operations:

Read and understand all instructions and warnings in this manual before operating the appliance. Save these 

• 

instructions for future reference.

Always leave safety grills and filters in place. Without these components, operating blowers could catch on to 

• 

hair, fingers and loose clothing.

NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers.

• 

NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of 

• 

self combustion is higher when the oil has been used several times.

NEVER cook on “open” flames under the range hood. Check deep-fryers during use: Superheated oil may be 

• 

flammable.

Cleaning:

The saturation of greasy residue in the blower and filters may cause increased inflammability. Keep unit clean 

• 

and free of grease and residue build-up at all times to prevent possible fires.

Filters must be cleaned periodically and free from accumulation of cooking residue (see 

• 

cleaning instructions

 

on Page 19). Old and worn filters must be replaced immediately.

Do not operate blowers when filters are removed. Never disassemble parts to clean without proper instruc-

• 

tions. Disassembly is recommended to be performed by qualified personnel only. Read and understand all 

instructions and warnings in this manual before proceeding.

* Subject to change without notice, please contact your local reseller for details.

Summary of Contents for PSD





























Reviews: