Spagna Vetro SV298 Series Installation Manual And User'S Manual Download

Page: 21 / 26

Page 19

Maintenance

(Continued)

Replacing J4 Type Halogen Light Fixture:

This range hood uses halogen light fixture: 20W 12V (Product ID: SV-ACS-HAL20W).

•

Make sure the range hood is unplugged or turn OFF breaker and the lights are cool to touch.

•

Place a flat-head screwdriver between light housing and hood body, gently pry up the light housing and search for the

•

metal clip.

Apply force to the metal clip and pull out the light fixture. Disconnect the power cable and discard the old light fix

•

ture.

Reverse the steps to install a new halogen light fixture. Turn ON breaker and range hood to test for operation.

•

Replacing J4 Type Halogen Light Bulb:

This range hood uses halogen light bulb: 20W 12V (Product ID: SV-ACS-HAL20W-B).

•

Make sure the range hood is unplugged or turn OFF breaker and the lights are cool to touch.

•

Place a small flat-head screwdriver between light housing and lens cover, carefully and gently pry up the lens cover.

•

Remove the old halogen light bulb by pulling in the direction of wavy arrow. Do not touch the new light bulb with

•

bare hands.

Reverse the steps to install a new halogen light bulb. Turn ON breaker and range hood to test for operation.

•

Replacing GU10 Type light bulb:

This range hood uses LED or halogen bulb (please refer to the actual specification of the hood purchased):

•

USA/Canada: Halogen 35W Type GU10 120V (Europe : 220V)

USA/Canada: LED 3W Type GU10 120V (Europe : 220V)

Make sure the range hood is unplugged or turn OFF breaker.

•

Make sure the lights are cool to touch, carefully align the ar

•

row on the inner ring with the arrow on the outer ring where it

says OPEN. The inner ring will loosen and the light bulb will

be available for removal. Install a new halogen light bulb and

reverse the steps.

Turn ON breaker and range hood to test for operation.

•

Light Housing

Flat-head

Screwdriver

Lens Cover

Halogen Bulb

Lens Cover

Align arrows on both rings

WARNING

Hazard of Burns!

Light bulb become extremely hot when turned on.

DO NOT touch bulb until switched off and cooled.

Touching hot bulbs could cause serious burns.

Light Housing

Hood

Body

Flat-head Screwdriver

Power Plug

Metal Clip

Summary of Contents for SV298 Series



























Search results

Summary of Contents for SV298 Series

Reviews:

Related manuals for SV298 Series

Brands by name

Popular brands

Spagna Vetro SV298 Series, Installation Manual And User'S Manual

Search results

Summary of Contents for SV298 Series

Reviews:

Related manuals for SV298 Series

Brands by name

Popular brands