background image

Max*: 101”

Page 5

Standard

Upper

Chimney

Extension available*

Range hood

Support 

Structure

Standard

Lower

Chimney

Extension available*

Min:

  

28” 

Max: 31”

36” base

Maximum* ceiling clearance 

101” at 31” hood mounting 

height above countertop/stove 

(may vary with different 

model). Chimney extensions 

available for higher ceiling.

* Higher ceiling requires chimney extension. 

Available at your local resellers.

Venting Requirements

Height & Clearance

Vent  system  must  terminate  to  the  outside 

• 

(roof or side wall).

DO NOT terminate the vent system in an at

-

• 

tic or other enclosed area.

DO NOT use 4” (10.2 cm) laundry-type wall 

• 

caps.

Use metal/aluminum vent only. Rigid metal/

• 

aluminum vent is recommended.

DO NOT use plastic vent.

• 

Always keep the duct clean to ensure proper 

• 

airflow.

Calculate the following figures before instal

-

• 

lation:

Distance from the floor to the ceiling.

1. 

Distance between the floor to the coun-

2. 

tertop/stove (recommend* 28” to 31”).

Distance  between  the  countertop/stove 

3. 

to the range hood.

Height of hood and duct cover.

4. 

For the most efficient & quiet operation:

A distance of 28” to 31” is recommended* 

• 

between stove top and the bottom of range 

hood.

It  is  recommended  that  the  range  hood  be 

• 

vented vertically through the roof through 6” 

(15.2 cm) or bigger round metal/aluminum 

vent work.

The size of the vent should be uniform.

• 

Use no more than three 90° elbows.

• 

Make  sure  there  is  a  minimum  of  24”  (61 

• 

cm) of straight vent between the elbows if 

more than one elbow is used.

DO NOT install two elbows together.

• 

The  length  of  vent  system  and  number  of 

• 

elbows should be kept to a minimum to pro

-

vide efficient performance.

The  vent  system  must  have  a  damper.  If 

• 

roof  or  wall  cap  has  a  damper,  DO  NOT 

use damper (if supplied) on top of the range 

hood.

Use silver tape or duct tape to seal all joints 

• 

in the vent system.

Use  caulking  to  seal  exterior  wall  or  roof 

• 

opening around the cap.

* Due to different ceiling height configurations, rec

-

ommended height may not be applicable.

Countertop/Stove

Summary of Contents for SV298 Series



























Reviews: