background image

 

-

 

Electrical equipment is designed to withstand to protect against the effects of transportation, and 

storage temperature within a range of -25

  to +55

  and for short periods not exceeding 24h at up 

to +70

 

Operating Instructions 

BEFORE USING THE MIXER 

Before using the mixer, ensure that all users are familiar with the correct operation of the machine. In 

particular, care should be taken to ensure that the bowl and mixing tools are correctly fitted and that the 

bowl guard is in position prior to starting the machine. 

SAFETY AT WORK 

-

 

NEVER place your hand or any kitchen utensil in the bowl whilst the mixer is in operation. 

-

 

Keep hands, hair and clothing away from moving parts. 

-

 

Isolate the machine from the electrical supply by removing the plug from the socket before 

cleaning, servicing or adjusting any parts or attachments. 

-

 

Do not use the machine with any cover or guard removed. 

-

 

Certain operator notice advising about the safe use of this mixer is attached to 

the machine. 

OFFICE, SHOPS AND RAILWAY PREMISES ACT, 1963 

The above Act requires that this machine and attachments shall be operated only by a properly 

instructed person or by an employee who is under the supervision of a properly instructed person. The 

instruction shall include indication of the possible dangers arising and the precautions to be observed. The 

Act also requires that no person under the age of 18 shall clean a machine if this exposes him to risk of 

injury from a moving part of that machine or any adjacent machine. 

CORRECT USE OF THE MIXER 

-

 

It is the responsibility of the operators to use the mixer correctly within the recommended 

limitations. Always follow the instructions on the side of the machine when changing gear. If the 

motor labors, please stop the machine and reduce the size of the mix immediately. Damage 

resulting from improper use is will void the warranty. 

-

 

For operator safety, the machine is fitted with a bowl guard which is electrically interlocker to 

ensure that the mixer cannot operate unless the guard is correctly positioned and the bowl is raised. 

Excessive force used to open and close the bowl guard may damage the electrically interlocker, and 

will void the warranty. 

-

 

For additional safety, the mixer has a no volt release feature which means that in the event of a 

power failure, the machine will only restart after the control button has been pressed again. This 

arrangement ensures that when the supply is restored, the machine cannot restart on its own. 

-

 

Careful handling of bagged products by minimizing the height above the bowl base from which they 

are poured. 

-

 

Careful slitting of bags in the lower part of the bowl to allow dust free discharge of flour as flour as 

possible. 

-

 

Use temporary bowl covers to minimize openings through which flour many escape. 

-

 

 

Operating Instructions 

 

Beater:

 Firm mixes such as light 

pastry, cakes biscuits, icings 

fillings and mashed vegetables. 

Summary of Contents for HI Series


















Reviews: