Sparta D-BURST M8TB Owner'S Handbook Manual Download

Page: 19 / 230

English –

activate

the push assistance, briefly press the

WALK

button on your on-board computer. After activation, press
the

button within 3 s and keep it pressed. The eBike drive

is switched on.

Note:

The push assistance cannot be activated at assistance

level

OFF

The push assistance is

switched off

as soon as one of the

following occurs:
– You release the

button;

– The wheels of the eBike are locked (e.g. by applying the

brakes or hitting an obstacle);

– The speed exceeds

km/h

The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.

Powering external devices via the USB port

The USB port can be used to operate or charge most devices
that can be powered via USB (e.g. various mobile phones).
Charging requires the on-board computer to be mounted
and a sufficiently charged battery to be inserted in the eBike.
Open the protective cap

(8)

for the USB port on the on-

board computer. Use a Micro-A – Micro-B USB charging
cable (available from your Bosch eBike dealer) to connect
the USB port on the external device to the USB port

(7)

the on-board computer.
Once the electrical load has been disconnected, the USB
port must be carefully resealed with the protective cap

(8)

USB connections are not waterproof. When cycling in the
rain, do not connect any external devices and make sure
that the USB port is fully sealed by the protective
cover

(8).

Important:

If electrical loads are connected, this can affect

the range of the eBike.

Displays and configurations of the
on-board computer

Speed and distance indicators

The

speedometer

(f)

always displays the current speed.

You can choose from the following functions in the

function

display

(combination of text indicator

(d)

and value indic-

ator

(e)

–

<Clock>:

Current time

–

<Max. speed>:

Maximum speed achieved since the last

reset

–

<Avg. speed>:

Average speed achieved since the last re-

set

–

<Trip time>:

Journey time since the last reset

–

<Range>:

Estimated range of the available battery

charge (at constant conditions such as assistance level,
route profile, etc.)

–

<Odometer>:

Total distance travelled with the eBike

(cannot be reset)

–

<Trip distance>:

Distance travelled since the last reset

switch between display functions

, press the

but-

ton

(1)

on the on-board computer or the

button

(10)

on the

operating unit repeatedly until the required function is dis-
played.
To reset the

<Trip distance>

<Trip time>

and

<Avg.

speed>

, switch to one of these three functions and then

press the

RESET

button

(6)

until the indicator is set to zero.

This will also reset the values of the other two functions.
To reset the

<Max. speed>

, switch to this function and then

press the

RESET

button

(6)

until the indicator is set to zero.

To reset the

<Range>

, switch to this function and then press

the

RESET

button

(6)

until the indicator is reset to the value

of the factory setting.
If the on-board computer is removed from the holder

(4)

, all

values of the functions are saved and can still be displayed.

Displaying/adjusting basic settings

The basic settings can be displayed and changed regardless
of whether the on-board computer is inserted in the holder

(4)

or not. Some settings can only be viewed and changed

when the HMI is inserted. Depending on the equipment of
your eBike, some menu items may not be present.
To go to the basic settings menu, simultaneously press the

RESET

button

(6)

and the

button

(1)

until

<Configura-

tion>

appears on the text indicator

(d)

switch between the basic settings