background image

GB

GB

 11

2.8 PREPARATION OF THE EXISTING FIREPLACE

•  Approval must be obtained from the heating inspector/chimney sweep 

for your district before the cassette is installed.

•  The chimney must be swept, examined and tested for leaks.
•  Check whether the open fireplace is suitable for installing a fireplace 

cassette.

•  Please note that the fireplace will be subjected to a higher level of stress 

after the cassette has been installed.

•  The existing open fireplace will be reduced in size due to the installation 

of necessary thermal insulation coatings.

IMPORTANT: 

Take into account the following conditions when measuring up 

for the fireplace cassette.

•  Shut-off dampers are to be completely opened in the exhaust gas sys-

tem and locked in place so that they cannot close. If required, they are 
to be totally removed.

•  The combustion air feed pipes that lead to the fireplace must not be 

closed. Ensure that there is sufficient combustion air (minimum 360 m³ 
per hour and m² of the firebox opening).

•   The fireplace cassette can be connected to a flexible exhaust gas flue, 

which is fed through the existing chimney flue. This flexible exhaust gas 
flue must correspond to DIN 1856-T2. (Manufacturer e.g.: Westaflex, 
type: MS-System or Haflex, type: 870s)

3. FIRE PROTECTION

3.1 FLOORING

In front of the openings to fireplaces with closed fireboxes, flooring made 
out of combustible materials must be protected by a covering of non-
combustible materials. The covering must extend outwards at the front by a 
minimum of 500 mm and at the sides by at least 300 mm from the fireplace 
opening (see Fig. 3).

The non-combustible covering can be made out of ceramics (e.g. tiles, flag-
stones), natural stone or other mineral construction materials (e.g. marble, 
granite), metal with a thickness of at least 1mm or glass of corresponding 
strength. The covering must be secured against dislocation.

A

B

XS 500

Floor covering

466 mm

S 600

566 mm

M 700

666 mm

L 800

766 mm

XL 900

866 mm

Fig.3

Summary of Contents for L 800





































Reviews: