background image

GB

GB

 13

3.6.1  MASONRY WORK FOR WALLS NEEDING 

PROTECTION

•  When installing the open fireplace on walls needing protection then 

masonry work is required. The masonry work must project at least 200 
mm above the flue pipes.

•  The masonry work (100 mm) can be dispensed with when the build-

ing’s alls are: 
- At least 115 mm thick 
- Made of non-combustible construction components 
- Not made of load-bearing concrete or reinforced concrete

•  The masonry work can be completed in a conventional way e.g. using 

bricks or can also be constructed out of so-called “thermal insulation 
panels” so that the overall construction depth - consisting of masonry 
work and thermal insulation - can be significantly reduced. Alternatively, 
the masonry work and the insulation can be completed using suitable 
insulation materials, see 3.6. This will enable the overall thickness to be 
reduced significantly.

3.7  EXPANSION JOINT BETWEEN THE CASING AND 

THE FIREPLACE CASSETTE

There must be no direct connection between the fireplace cassette and the 
casing. An expansion joint is to be fitted that should be connected using e.g. 
a sealing strip. Please note that there must be a minimum distance of 6 mm 
between the door frame and the fireplace apron to enable the firebox door 
to be dismantled if required.

3.8 COMBUSTION CHAMBER DESIGN

Design A
No recirculating or primary air cross section openings need to be produced.

Combustion chamber spacings

Linear cassette

Setup floor

Mounting wall

Ceiling

Side wall

XS 500

40 mm

60 mm

200 mm

60 mm

S 600

40 mm

10 mm

200 mm

10 mm

M 700

40 mm

10 mm

200 mm

10 mm

L 800

40 mm

10 mm

200 mm

10 mm

XL 900

40 mm

10 mm

200 mm

10 mm

Rock wool mats to AGI Q-132)

Linear cassette

Setup floor

Mounting wall

Ceiling

Side wall

XS 500

0 mm

50 mm

50 mm

60 mm

S 600

0 mm

200 mm

190 mm

170 mm

M 700

0 mm

200 mm

190 mm

170 mm

L 800

0 mm

200 mm

190 mm

180 mm

XL 900

0 mm

200 mm

170 mm

180 mm

Summary of Contents for L 800





































Reviews: