Spearhead RC
132/162
2
IMPORTANT
VERIFICATION OF WARRANTY REGISTRATION
DEALER WARRANTY INFORMATION & REGISTRATION VERIFICATION
It is imperative that the selling dealer registers this machine with Spearhead Machinery Limited
before delivery to the end user
– failure to do so may affect the validity of the machine warranty.
To register machines go to the Spearhead Machinery Limited web site at
www.spearheadmachinery.com
, log onto ‘
Dealer Inside
’ and select the ‘
Machine Registration
button
’ which can be found in the Service Section of the site. Confirm to the customer that the
machine has been registered in the section below.
Should you experience any problems registering a machine in this manner please contact the
Spearhead Service Department on 01789 491867.
Registration Verification
Dealer Name:
Dealer Address:
Customer Name:
Date of Warranty
Registration:
/ /
Dealer Signature:
NOTE TO CUSTOMER / OWNER
Please ensure that the above section has been completed and signed by the selling dealer to
verify that your machine has been registered with Spearhead Machinery Limited.
IMPORTANT: During the initial ‘bedding in’ period of a new machine it is the customer’s
responsibility to regularly inspect all nuts, bolts and hose connections for tightness and re-
tighten if required. New hydraulic connections occasionally weep small amounts of oil as the
seals and joints settle in
– where this occurs it can be cured by re-tightening the connection –
refer to torque settings
chart below.
The tasks stated above should be performed on an hourly
basis during the first day of work and at least daily thereafter as part of the machines general
maintenance procedure.
CAUTION: DO NOT OVER TORQUE HYDRAULIC FITTINGS AND HOSES
TORQUE SETTINGS FOR HYDRAULIC FITTINGS
HYDRAULIC HOSE ENDS
PORT ADAPTORS WITH BONDED SEALS
BSP
Setting
Metric
BSP
Setting
Metric
1/4”
18 Nm
19 mm
1/4”
34 Nm
19 mm
3/8”
31 Nm
22 mm
3/8”
47 Nm
22 mm
1/2”
49 Nm
27 mm
1/2”
102 Nm
27 mm
5/8”
60 Nm
30 mm
5/8”
122 Nm
30 mm
3/4”
80 Nm
32 mm
3/4”
149 Nm
32 mm
1”
125 Nm
41 mm
1”
203 Nm
41 mm
1.1/4”
190 Nm
50 mm
1.1/4”
305 Nm
50 mm
1.1/2”
250 Nm
55 mm
1.1/2”
305 Nm
55 mm
2”
420 Nm
70 mm
2”
400 Nm
70 mm
Summary of Contents for RC 132
