4
RHD OFFSET SERIES
160/190/225
General Information
Always read this manual before fitting or operating the machine – whenever any doubt
exists contact your dealer or the Spearhead Service Department for advice and
assistance.
Use only Spearhead Genuine Parts on Spearhead Equipment and Machines
DEFINITIONS
–
The following definitions apply throughout this manual:
WARNING
An operating procedure, technique etc., which –
can result in personal injury or loss of life if not observed carefully.
CAUTION
An operating procedure, technique etc., which –
can result in damage to either machine or equipment if not observed carefully.
NOTE
An operating procedure, technique etc., which –
is considered essential to emphasis.
LEFT AND RIGHT HAND
This term is applicable to the machine when attached to the tractor and is viewed
from the rear – this also applies to tractor references.
Machine description and purpose of use
The RHD PLUS series of machines are ‘3-point linkage’ tractor mounted universal flail
mower/shredders designed primarily for the mulching of grasses, brambles, small bushes,
branches, vines, and general crop residues. Their tough construction, working widths of 1.6,
1.9 or 2.25m and offset makes them ideal for maintenance use in all green areas, vineyards,
orchards, on verges and in scrubland by farmers and contractors alike.
These machines should only be used to perform tasks for which they were designed – use of
the machine for any other function may be both dangerous to persons and damaging to
components and is therefore not advisable.
Summary of Contents for RHD OFFSET 160
