background image

M017837080000 REV. January 19, 2011

2EZ Speed

TM

 Pool Motor with Programmable Control/Timer

2EZ Speed

TM

 Motor Control/Timer Speci cations

•   

 The 2EZ Speed

TM

 motor control is designed to operate from 

a typical U.S. residential single-phase 230 volt line supply. 

Operational voltage range – 207-253 VAC 60 hertz. 

•  

 The motor operates at two speeds; high speed 

(approximately 3450 RPM) and low speed  

(approximately 1725 RPM).

•  

 Maximum continuous current: See motor nameplate 

for motor rating, control rated for 14.0 amps maximum.

About the 2EZ Speed

TM

 Motor/Control

The 2EZ Speed

TM

 motor and timer is an easy-to-install two-

speed pool pump motor with an integrated programmable 

timer, designed to achieve maximum energy efficiency and 

utility dollar savings.

    Easy Installation:

 Drop-in design allows for fast 

replacement of your existing pool motor.

    Easy Programming:

 Supplied with default speed 

settings – Just set the time and day of the week and  

the timer does the rest! To customize your speed 

settings, provide on and off times for Low and  

High Speeds!

    Energy Ef cient:

 Did you know that you can save the 

most energy by maximizing your low speed operation, 

and yet still clean your pool, just by customizing your 

settings? To determine your energy savings, try our 

energy calculator online:  

www.nidec-motor.com/Pool

 

Mounted on the 2EZ Speed

TM

 motor is a user interface 

which allows the pool owner to easily control the operating 

times and motor speeds. Schedules can be programmed 

for weekdays: Monday through Friday and weekends: 

Saturday and Sunday. 

Motor Features

•  

2 Speed – Permanent Split Capacitor Single Phase Motor

•  

56 Frame (Offered in both Square and C-Face)

•  

 HP thru 2 HP Full Rated

•  

High Efficiency

•  

Switchless

•  

Easy to Operate Programmable User Interface

•  

Freeze Sensor

•  

Designed for Quiet Operation

•  

Single Phase Motor

•  

Meets Title 20 Legislation

Timer/Control

User Interface  

w/Cover

Motor

Terminal 

Cover

IMPorTAnT SAFETy InSTruCTIonS

2EZ Speed

TM

 Motor Control/Timer Installation   Maintenance Manual

Save this Instruction Manual for future reference.

Table of Contents

Motor Control/Timer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 
About the 2EZ Speed

TM

 Motor Control/Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3 

Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5 
General Installation Instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 
Basic Motor/Timer Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 
User Interface Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9 
Quick Start Programming  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 
Detail Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13 
How to Connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 
Freeze Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 
Locking the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 
Operating the 2EZ Speed

TM

 Pool Motor/Control 

                with other Equipment Pad Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 
General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 
How to Lower Utility Bills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 
Recommended Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 

For Technical Assistance or Questions related to your 2EZ Speed

TM

 Motor Control/Timer:

Call our Pool Motor Product Services Hotline:

1-

- 66-1 1

or email questions to:

motorhelp nidec-motor.com

or visit our web site at:

www.nidec-motor.com/pool

Summary of Contents for BADU ECOM2/S90





























Reviews: