background image

Part # M017898010000   August 31, 2012

27

ECOTECH EZ

®

 Variable Speed Motor/Control

Recommended Maintenance

WARNING

!

 

Before performing any maintenance, 

disconnect the power, allow the motor to come to a 

complete stop and wait five minutes. This will allow the 

control capacitors to safely discharge any residual voltage.

Periodically inspect the installation. Check for dirt 

accumulations, unusual noises or vibration, overheating, 

worn or loose couplings, high motor amps, poor wiring  

or overheated connections, and for loose mounting bolts  

or guards.

Remove dirt accumulation, particularly in and around  

the ventilation openings on the motor by vacuuming.  

Dirt accumulations can cause motor overheating and  

a fire hazard.

Do not use any type of solvents! Some solvents may 

attack the motor insulation, finish or bearing lubricants. 

Solvents are also highly flammable.

This motor contains ball bearings which are permanently 

lubricated. No maintenance is required. 

LIMITED WARRANTY

Nidec Motor Corporation extends the following LIMITED 

WARRANTY to the purchaser and to its customers 

(collectively referred to as the “Purchaser”) of the enclosed 

motor and components: the motor and components are 

free from defects in materials and workmanship under 

normal use, service and maintenance FOR A PERIOD 

OF 18 MONTHS FROM THE DATE OF ORIGINAL 

PURCHASE FROM NIDEC MOTOR CORPORATION 

OR THE NIDEC MOTOR CORPORATION DEALER/

RETAILER, NOT TO EXCEED 24 MONTHS FROM 

THE DATE OF MANUFACTURE BY NIDEC MOTOR 

CORPORATION. THE FOREGOING WARRANTY 

IS THE ONLY WARRANTY GIVEN AND NO OTHER 

WARRANTY IS PROVIDED, EXPRESS OR IMPLIED, 

INCLUDING WITHOUT LIMITATION, MERCHANTABILITY 

OR FITNESS FOR A PARTICULAR PURPOSE. Certain 

aspects or disclaimers are not applicable to consumer 

products, i.e., motors and components acquired by 

individuals and used for personal, family or household 

purposes (as distinguished from industrial or other 

purposes). Some states do not allow

 

limitations on how 

long an implied warranty lasts, so the above limitation may 

not apply to you. This warranty gives you specific legal 

rights, and you may have other rights which vary from 

state to state.

Certain repairs or services are the responsibility of 

the Purchaser and the Purchaser is expected to 

pay for them. This warranty does not extend to any 

losses or damages due to misuse, accident, abuse, 

neglect, negligence, unauthorized modification or 

alteration, use beyond rated capacity, or improper 

installation, maintenance, application or use, including, 

without limitation, use in a manner contrary to the 

accompanying instructions or applicable codes. 

If within thirty (30) days after Purchaser’s discovery of 

any warranty defects within the above stated warranty 

period, Purchaser notifies Nidec Motor Corporation or the 

dealer from whom the motor was purchased in writing, 

Nidec Motor Corporation shall, at its option and as 

Purchaser’s sole and exclusive remedy, repair or replace 

or refund the purchase price for, that portion of the motor 

and components found by Nidec Motor Corporation to 

be defective. Failure by Purchaser to give such written 

notice within the applicable time period shall be deemed 

an absolute and unconditional waiver of Purchaser’s 

claim for such defects. Purchaser must write or call the 

dealer from whom the motor was purchased for directions 

regarding the shipment of the motor, with freight pre- or 

call the dealer from whom the motor was purchased for 

directions regarding the shipment of the motor, with freight 

prepaid by the Purchaser, to an authorized service location 

for warranty service. If Purchaser is unable to contact 

the dealer to obtain sufficient instructions regarding the 

handling of the motor, Purchaser should write Nidec 

Motor Corporation at the address on the back cover of 

this manual, giving the model number, the dealer’s name, 

address and number of dealer’s invoice; and describing 

the nature of the alleged defect. Arrangements for warranty 

service will then be made by Nidec Motor Corporation. If 

the motor is damaged in transit, Purchaser should file a 

claim directly with the carrier.

IN NO EVENT, REGARDLESS OF THE FORM OF THE 

CLAIM OR CAUSE OF ACTION (WHETHER BASED 

IN CONTRACT, INFRINGEMENT, NEGLIGENCE, 

STRICT LIABILITY, OTHER TORT OR OTHERWISE), 

SHALL NIDEC MOTOR CORPORATION’S LIABILITY 

TO PURCHASER OR ITS CUSTOMER EXCEED THE 

PRICE PAID BY PURCHASER FOR THE SPECIFIC 

MOTOR OR OTHER GOODS PROVIDED BY NIDEC 

MOTOR CORPORATION GIVING RISE TO THE CAUSE 

OF ACTION. IN NO EVENT SHALL NIDEC MOTOR 

CORPORATION’S LIABILITY TO PURCHASER OR 

ITS CUSTOMER EXTEND TO INCLUDE INCIDENTAL 

CONSEQUENTIAL OR PUNITIVE DAMAGES, WITH 

RESPECT TO CONSUMER PRODUCTS, SOME STATES 

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF 

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE 

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY 

TO YOU. 

Pool Motor Product Service Hotline: 

1-800-566-1418 

www.nidec-motor.com/pool

8050 W. Florissant Avenue | St. Louis, MO 63136

Phone: 888-637-7333 | Fax: 314-553-2087 

www.nidec-motor.com

 | 

www.usmotors.com 

Nidec Motor Corporation, 2011; All Rights Reserved. 

 

U.S. MOTORS

®

 is a registered trademark of Nidec Motor Corporation. 

Nidec Motor Corporation trademarks followed by the ® symbol are 

registered with the U.S. Patent and Trademark Office.

Summary of Contents for Badu EcoMV







































Reviews: