background image

Spectracom Corporation 

 

EPSILON CLOCK MODEL EC22S 

 EPSILON CLOCK User’s Manual 

1-7 

 

1.8

1.8

1.8

1.8

 

Dimensions

Dimensions

Dimensions

Dimensions and Weight

 and Weight

 and Weight

 and Weight    

Width: 

 

19" (441 mm), without bracket 

Height: 

 

2 U (88 mm).   

Depth: 

 

400 mm + 40 mm (front panel handles). 

Weight: 

 

<6.5 kg. 

Compatiblity

: 19” rack 

 

1.9

1.9

1.9

1.9

 

Operating Environment

Operating Environment

Operating Environment

Operating Environment    

- Operating temperature: 

0 to 50°C 

- Storage temperature: 

-40 to 85°C 

- Relative humidity:  

95 % non-condensing 

- Electromagnetic compatibility:  

in accordance with EN30386/EN55022/EN60950 

 

1.10

1.10

1.10

1.10

 

Power

Power

Power

Power Supply

 Supply

 Supply

 Supply    

1.10.1 DC Power Supply Input 

Nominal DC input voltage:  

-48 Volts 

Normal variation:   

 

-40 to - 57 Volts 

Transitory variation:  

 

-37 to - 72 Volts 

Nominal DC input voltage conditions:  

-48 Volts DC 

Maximum Total Power consumption:  

< 55 W 

 

Two independent input, two connectors 

Protection against polarity reversal 

-48V and 0V DC input wires are not ground referenced 

Every module protected by a PolySwitch fuse (automatically rearmed) 

-   Detection of power input presence on each connector, information available on LCD display 

or with remote control software, threshold level of detection between -35 and -40 Volts 

 

1.10.2 AC Power Supply Input 

Nominal AC input voltage: 90 to 264 Volts AC / 48 to 63 Hz 

Two independent power input, two connectors/switches 

-   On each switch: 2 fuses: D1TD 2A 5x20 
-   Detection  of  power  input  presence  on  each  AC/DC  converter,  information  available  with 

remote control software 

 

1.10.3 Redundancy 

Power supply redundancy exists at two levels: between AC and DC and between Left and Right 
module converters. 

If the AC Input power supply is present, DC input is internally disconnected. If AC input fails, DC 
input switches over to supply the equipment. 

Summary of Contents for EC22S





































































Reviews: