background image

 

 

  

 IO-AI8

 

    I/O Expansion Module       8 Analog Inputs

  

 

The IO-AI8 is an I/O Expansion Module that 
can be used in conjunction with specific 
Unitronics OPLC controllers. 
The module offers 8 analog inputs. 
The interface between the module and the 
OPLC is provided by an adapter. 
The module may either be snap-mounted 
on a DIN rail, or screw-mounted onto a 
mounting plate.

 

 

Component identification 

1 Module-to-module 

connector 

2 Communication 

status 

indicator 

Input connection points, AN4 to 
AN7 

Input status indicators  

Module-to-module connector port 

Input connection points, AN0 to 
AN3 

 

 

 

„

 

Before using this product, it is the responsibility of the user to read and understand this 
document and any accompanying documentation. 

„

 

All examples and diagrams shown herein are intended to aid understanding, and do not 
guarantee operation.  Unitronics accepts no responsibility for actual use of this product based on 
these examples. 

„

 

Please dispose of this product in accordance with local and national standards and regulations. 

„

 

Only qualified service personnel should open this device or carry out repairs. 

 

User safety and equipment protection guidelines 

This document is intended to aid trained and competent personnel in the installation of this equipment as 
defined by the European directives for machinery, low voltage, and EMC.  Only a technician or engineer 
trained in the local and national electrical standards should perform tasks associated with the device’s 
electrical wiring. 

Symbols are used to highlight 
information relating to the user’s 
personal safety and equipment 
protection throughout this document.  
When these symbols appear, the 
associated information must be read 
carefully and understood fully. 

Symbol Meaning 

Description 

Danger 

The identified danger causes physical 
and property damage. 

Warning 

The identified danger can cause 
physical and property damage. 

Caution

  

Caution Use 

caution. 

 

 

„

 

Failure to comply with appropriate safety guidelines can result in severe personal injury 
or property damage.  Always exercise proper caution when working with electrical 
equipment. 

Spectra GmbH & Co. KG
vertrieb@spectra.de

Spectra (Schweiz) AG
info@spectra.ch

Summary of Contents for Unitronics IO-AI8









Reviews: