background image

Introduction ........................................................................................................................ 1

Specifications ...................................................................................................................... 1

Safety Precautions............................................................................................................. 2

Unpacking ............................................................................................................................ 2

Front Panel ........................................................................................................................... 3

Rear Panel ............................................................................................................................. 4

Installation ........................................................................................................................... 4

Operation ............................................................................................................................. 7

Technical Support ............................................................................................................. 9

Table of Contents

Summary of Contents for PRISMA VelaSync













Reviews: