background image

SpectraLink Corporation 

Installation and Administration  

 

NetLink OAI Gateway 

Notice 

SpectraLink Corporation has prepared this document for use by SpectraLink personnel and customers.

 

The 

drawings and specifications contained herein are the property of SpectraLink and shall be neither reproduced in 

whole or in part without the prior written approval of SpectraLink, nor be implied to grant any license to make, 
use, or sell equipment manufactured in accordance herewith. 

SpectraLink reserves the right to make changes in specifications and other information contained in this 
document without prior notice, and the reader should in all cases consult SpectraLink to determine whether 

any such changes have been made. 

The terms and conditions governing the sale of SpectraLink hardware products and the licensing of 

SpectraLink software consist solely of those set forth in the written contracts between SpectraLink and its 
customers. No representation or other affirmation of fact contained in this document including but not limited 

to statements regarding capacity, response-time performance, suitability for use, or performance of products 
described herein shall be deemed to be a warranty by SpectraLink for any purpose, or give rise to any liability of 

SpectraLink whatsoever. 

In no event shall SpectraLink be liable for any incidental, indirect, special, or consequential damages 

whatsoever (including but not limited to lost profits) arising out of or related to this document, or the 
information contained in it, even if SpectraLink has been advised, knew, or should have known of the 

possibility of such damages. 

Trademark Information 

SpectraLink 

The SpectraLink logo 
LinkPlus 

Link  
NetLink  

SVP 

Are trademarks and registered trademarks of SpectraLink Corporation. 

All other trademarks used herein are the property of their respective owners. 

SpectraLink Corporation 

5755 Central Avenue 

Boulder, CO 80301 
Within the United States, dial 

303.440.5330 or 
toll free 800.676.5465 

Outside the U.S., dial 
+1.303.440.5330 
www.spectralink.com 

Copyright © 1998 to 2006 SpectraLink Corporation. All rights reserved 

Information in this document is subject to change without notice and does not represent a commitment on the 

part of SpectraLink Corporation. The software described in this document is furnished under a license and/or 
copyright and may only be used with the terms of SpectraLink’s software license agreement as found in this 

manual or at 

http://www.spectralink.com/consumer/resources/software_updates.jsp

. The software may be 

used only in accordance with the terms of the agreement. No part of this manual, or the software described 

herein, may be reproduced or transmitted in any form or by any means, electronic or mechanical, including 
photocopying and recording, for any purpose except for the sole intent to operate the product or without the 

express written permission of SpectraLink Corporation. 

 

PN: 72-0078-07-B.doc  

Page 2 

Summary of Contents for MOG600




































Reviews: