background image

SpectraLink Corporation 

Installation, Setup, and Maintenance 

NetLink SVP Server 

Part Number: 72-0178-00-J.doc 

Page 3 

Note concerning the NetLink SVP Server: 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense. 

Note concerning shielded cable: 

SpectraLink recommends the use of shielded cable for all external signal connections in order to maintain 
FCC Part 15 emissions requirements. 

Note concerning the NetLink Wireless Telephones: 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 

WARNING

 

Changes or modifications to this equipment not approved by SpectraLink Corporation may 

cause this equipment to not comply with part 15 of the FCC rules and void the user’s authority to operate 
this equipment. 

WARNING

 

SpectraLink products contain no user-serviceable parts inside. Refer servicing to qualified 

service personnel. 

Important Safety Information 

Follow these general precautions while installing telephone equipment: 

• 

Never install telephone wiring during a lightning storm. 

• 

Never install telephone jacks in wet locations unless the jack is specifically designed 
for wet locations. 

• 

Never touch uninsulated telephone wires or terminals unless the telephone line has 
been disconnected at the network interface. 

• 

Use caution when installing or modifying telephone lines. 

Summary of Contents for NetLink SVP Server







































Reviews: