background image

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

23

THREE YEAR LIMITED WARRANTY

Effective on products purchased after March 10, 2005. 

All standard water purification products manufactured by SpectraPure have a 3 year limited warranty, except 
the Eliminator™ MarinePro™, Industrial, Laboratory, Custom Systems, and electrical products which have a 1 
year limited warranty. LiterMeters™ have a 2 year limited warranty. OEM equipment resold by SpectraPure 
carry the original manufacturer’s warranty. 
SpectraPure, Inc.® warrants the product to the original owner only to be free of defects in material and 
workmanship for a period of three years (see exceptions above) from the date of receipt. SpectraPure’s liability 
under this warranty shall be limited to repairing or replacing at SpectraPure’s option, without charge, F.O.B. 
SpectraPure’s factory, any product of SpectraPure’s manufacture. SpectraPure will not be liable for any cost of 
removal, installation, transportation or any other charges which may arise in connection with a warranty claim. 
Products which are sold but not manufactured by SpectraPure are subject to the warranty provided by the 
manufacturer of said products and not by SpectraPure’s warranty. SpectraPure will not be liable for damage or 
wear to products caused by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration 
or repair or, if the product was not installed in accordance with SpectraPure’s or other manufacture’s printed 
installation and operating conditions, or damage caused by hot water, freezing, flood, fire or
acts of God. 
SpectraPure will not be responsible for any consequential damages arising from installation or use of the 
product, including any water or mold damage due to flooding which may occur due to malfunction or faulty 
installation, including, but not limited to failure by installer to over- or under-tighten fittings, housings, and/or 
push-style fittings, or improper installation of push-style fittings. 
SpectraPure warrants (pro-rated) the performance of tested SpectraSelect™ RO membrane elements only, for 
one year from date of receipt by the buyer, providing that the loss of performance was not caused by fouling , 
neglect or water conditions exceeding the feed water parameters listed in the applicable product manual (refer 
to detailed membrane warranty information). SpectraPure will, on confirmation of loss of performance during 
the warranty period, credit the pro-rated amount of the current catalog price of the element. The disposable 
filters and cartridges are not covered under the warranty. 
To obtain service under this warranty, the defective system or components must be returned to SpectraPure 
with proof of purchase, installation date, failure date and supporting installation data. Any defective product 
to be returned to the factory must be sent freight prepaid; documentation supporting the warranty claim and 
a Return Goods Authorization (RGA) number must be included. SpectraPure will not be liable for shipping 
damages due to the improper packaging of the returned equipment and all returned goods must also have 
adequate insurance coverage and a tracking number. 
SpectraPure will not pay for loss or damage caused directly or indirectly by the presence, growth, proliferation, 
spread or any activity of “fungus”, wet or dry rot or bacterica. Such loss or damage is excluded regardless of 
any other cause or event that contributes concurrently or in any sequence to the loss. We will not pay for loss 
or damage caused by or resulting from continuous or repeated seepage or leakage of water, or the presence 
or condensation of humidity, moisture or vapor, that occurs over a period of 14 days or more. “Fungus” and 
“fungi” mean any type or form of fungus or Mycota or any by-product or type of infestation produced by 
such fungus or Mycota, including but not limited to, mold, mildew, mycotoxins, spores, scents or any biogenic 
aerosols. 
SpectraPure will not be liable for any incidental or consequential damages, losses or expenses arising from 
installation, use, or any other causes. There are no expressed or implied warranties, including merchantability 
or fitness for a particular purpose, which extend beyond those warranties described or referred to above.

* The three year limited warranty does not apply to consumable items, including but not 

limited to, filters and cartridges unless specifically stated above.

Summary of Contents for Coffee Lovers System CLS-5-90

























Reviews: