SpectraPure Drinking Water Kit Instructions Manual Download

Page: 16 / 16

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

REPLACEMENT PARTS:

Part Number

Part

Description

CF-IN-10-6JG

10" inline post carbon filter

Polishes water and removes any taste

V-ASO -4JG

ASO Valve

Completely shuts off Product water and Waste water

V-CK-IL-1LB -4JG

Check Valve

Used in conjunction with the ASO Valve.

OPTIONAL PARTS:

Part Number

Description

PPRFK-DI

Permeate Pump Retrofit Kit used for RO/DI systems

BPLF-PS -115

Booster pump kit for use with up to 25-60 GPD system

BPHF-PS-115

Booster pump kit for use with over 60 GPD systems

V-PREG -0 -125-4GJ

Pressure reducing valve (pressure regulator)

TANK-SN03-4

3 Gallon Pressurized Storage Tank

TANK-SN04-4

4 Gallon Pressurized storage Tank

Summary of Contents for Drinking Water Kit

















Search results

Summary of Contents for Drinking Water Kit

Reviews:

Related manuals for Drinking Water Kit

Brands by name

Popular brands

SpectraPure Drinking Water Kit, Instructions Manual

Search results

Summary of Contents for Drinking Water Kit

Reviews:

Related manuals for Drinking Water Kit

Brands by name

Popular brands