background image

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

16

Problem

Cause

Corrective Action

4.

Red light on OPTIONAL 
push to test button monitor 
comes on - When RO water 
stored in tank is being 
tested.

a.

TDS build-up in the 
bladder tank.

i.

Drain tank completely and re-
test TDS.

b.

Bad membrane.

ii.

Replace membrane.

c.

Faulty monitor/probe.

iii.

Replace monitor/probe.

5.

Red light on OPTIONAL 
push-to-test button 
monitor comes on - When 
membrane product water is 
being tested.

a.

Bad membrane.

i.

Replace membrane.

b.

Faulty monitor/probe.

ii.

Replace monitor/probe.

6.

Water smells bad.

a.

Bacterial contamination 
of bladder tank.

i.

Sanitize RO/DI System.

b.

Ruptured bladder in 
storage tank.

ii.

Replace tank.

c.

Exhaused post carbon 
fi lter.

iii.

Replace post carbon fi lter.

7.

Milky  colored water.

a.

Air in system.

i.

Air in the system is a normal 
occurrence with initial start-
up of the RO/DI system. 
This milky appearance will 
disappear during normal use 
within 1-2 weeks. If condition 
reoccurs after fi lter changes, 
drain tank 1 to 2 times.

8.

Reject (yellow) line never 
stops fl owing water. 

a.

Faulty 3 lb. elbow 
check valve.

i.

Replace it.

b.

Faulty auto shut-off 
valve.

ii.

Replace it.

9.

Broken faucet handle.

a.

i.

Purchase a faucet repair kit.

10.

Leak under the faucet 
handle.

a.

i.

Purchase a faucet repair kit.

11.

Leak around the base of the 
spout.

a.

Displaced O-rings.

i.

Pull the faucet spout out. Seat 
O-rings in place.

b.

Worn O-rings.

ii.

Replace O-rings (Purchase a 
faucet repair kit).

12.

Noise from faucet or drain.

a.

Location of drain 
saddle.

i.

See 

page11 

for proper 

location of drain saddle.

Summary of Contents for DWS



















Reviews: