2 / 4
68272
2-1/8"
54 mm
1-1/2"
38 mm
MMMYYWWSSSSSSS
12345
W
W
W
W
W
W
W
W
W
M
M
MMMYYWWSSSSSSS
1234
5
W
W
W
W
W
W
W
W
W
M
M
Red:
Door handing was unsuccessful. Make
sure the lock interior and batteries are
correctly installed. Perform step 5B again.
If the door handing process is still
unsuccessful after a second attempt, see the
Manual Door Handing section on page 4.
NOTE
: The lock will auto-hand again
after the first time the door is locked or
unlocked using the keypad or app. This
is to confirm the door orientation.
Green:
Door
handing was
successful.
Proceed to
next step.
Status
LED
If the bolt does not move, make
sure the batteries are correctly
installed, and perform step 5B again.
Note: The latch bolt will
only retract
half way
.
actual size
For Lock
Bag
(2x)
69316
What is the diameter of the hole in the door?
Install 4 AA batteries in
the battery pack.
With the door open,
install the battery pack to
initiate auto-handing.
The latch will retract and extend to
learn the orientation of the door.
The Status LED will indicate success or failure.
Locate the screws for step 3D and keep them within reach.
Install the exterior keypad and mounting plate.
A
A
B
C
D
B
D
Diameter is 2-1/8"
(54 mm)
Diameter is 1-1/2"
(38 mm)
or
Adapter Ring is required
for installation. Install on
Exterior Assembly.
Adapter Ring is not
needed for installation
and may be discarded.
The cable goes
underneath the latch.
Support the exterior
assembly during mounting
plate installation.
Route the cable
through the center
hole, then push it into
the bottom hole.
Insert the key and
test the latch. If
the latch does not
extend or retract
smoothly,
adjust
the screws.
Remove the key
when finished,
and make sure
the latch bolt is
fully extended.
Keep parallel to the
edge of the door.
Make sure the torque blade is
centered in the mounting plate hole.
torque
blade
Tighten screws
evenly.
DO NOT
over
tighten screws.
a
c
b
d
Ensure correct polarity.
For best results, use
new, non-rechargeable
Alkaline batteries only.
MMMYYWWSSSSSSS
12345
W
W
W
W
W
W
W
W
W
M
M
69316
(2x)
(For
Lock Bag)
Ensure the turnpiece shaft is pointing up, and remove the interior cover and
battery pack from the interior assembly.
Install the interior assembly onto the mounting plate.
A
B
a
c
b
d
If the turnpiece shaft
is pointing down,
place the cover back
onto the interior
assembly and rotate
the turnpiece until
you hear it click.
You may need to
apply some force.
Once the turnpiece
shaft is correctly
oriented, remove
the cover again.
Make sure turn
piece shaft is
rotated as shown.
Do not install
batteries
until step 5.
Ensure tight cable
connection.
Lay the excess cable
flat inside the bottom of
the interior housing.
align
a
c
b
d
bottom
hole
If turnpiece shaft is not oriented
correctly, put the cover back on and
rotate the turnpiece as shown in step C.
Remove the interior
cover from the
interior assembly.
Incorrect:
Ensure you are using the correct
screws. Using incorrect screws
will damage the product.
actual size
For Lock
Bag
(2x)
Remove the mounting plate from the interior assembly.
C
68272
(2x)
68272
(2x)
(For Lock Bag)
3
Install the exterior keypad
4
Install the interior assembly
5
Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
Note: the
remaining three
screws will be
used in Step 9.
