background image

13

SPEKTRUM DX5C • TRANSMITTER INSTRUCTION MANUAL

EN

MENU

SETTINGS

System settings allow adjustments to the following transmitter settings:

Display

User Name 

The User Name fi eld displays the user name above the model name on the main screen.

1. 

Scroll to the desired letter position and click the scroll wheel once. A fl ashing box appears.

2. 

Scroll Up or Down until the desired character appears. Click the scroll wheel once to save the character.

3. 

Scroll to the next desired letter position. Repeat Steps 1 and 2 until the Model Name is complete. 

Language:

Change the transmitters language. The transmitter will retain the language for models already created. New 

models will be created using the currently selected language.

Contrast

To adjust the screen contrast:

1. 

Scroll to Contrast and click the scroll wheel.

2. 

Scroll Up or Down to adjust the contrast value. Lower numbers lighten the contrast, higher numbers 
darken it.

3. 

Click the scroll wheel once to save the selection.

• Display

• Trims

• Sounds

• About

• Calibrate

• Battery

Inactive Alarm:

An alarm activates if the transmitter sees a period of inactivity for a certain amount of time. The alarm is 
helpful in reminding you to power off the transmitter and avoiding a situation where the transmitter battery 
completely discharges.

•  Inh (No alarm sounds)
• 5 min

•  10 min (Default)
• 30 min

• 60 min

Trims

Assign Trims to any trimmer or switch on the transmitter.

1. 

Select the Trim position from the list.

2. 

Push the scroll wheel once to select the position.

3. 

Scroll to select the Trim desired in that position.

4. 

Click the scroll wheel to save the selection.

Sound settings

Turn system sounds ON/OFF.

1. 

Select the sound from the list.

2. 

Push the scroll wheel once to Activate/Inhibit.

3. 

Click the scroll wheel to save the selection.

TIP:

 Try deactivating the Roller sounds 

but leave the Keyclick active.

About

Displays the transmitter’s Serial Number. Start a user account at SpektrumRC.com and enter the serial number 
displayed on the About page register the transmitter. 

Summary of Contents for DX5C























Reviews: