Spectrum DX8G2 Instruction Manual Download

Page: 23 / 53

SPEKTRUM DX8G2 • TRANSMITTER INSTRUCTION MANUAL

Wireless Trainer works just like the Wired Trainer, without the wire.

Select Wireless Trainer to bind a DSM2 or DSMX slave transmitter

to the master transmitter. With this option, when the master press-

es the trainer button or switch, control is given to the currently

bound slave transmitter. After binding, the slave transmitter will

remain bound to the master transmitter until a different transmitter

is bound to the master, or the slave transmitter is bound to another

receiver or a wireless master transmitter. ModelMatch™ technol-

ogy applies to the wireless trainer system; the master transmitter

will be bound to the slave in the bound model used. Also, if the

slave transmitter has ModelMatch technology, it will only be bound

to the master transmitter in the selected model during binding.

Inhibit

In Inhibit, the wireless trainer function will be inhibited

and will not function.

CAUTION:

Select Inhibit in the Trainer menu when you aren’t

using the wireless trainer function. Failure to select Inhibit may

result in loss of control of the aircraft.

Programmable Master

Programmable mode enables you to program the master

transmitter to transfer any or all individual channels when you

activate the trainer switch. This mode is ideal for beginners

learning to control individual channels while the master transmitter

maintains control of all other channels. The slave transmitter

should be in Inhibit mode, if available. The Master and Slave

transmitters MUST have the same programming.

Pilot Link Master

Pilot Link Master enables you to program the master transmitter

to transfer any or all individual channels when you activate the

trainer switch. Pilot Link Master is ideal for complex models, as the

master transmitter maintains control of all secondary functions,

such as flight modes, retracts, flaps and brakes.

Secondary functions can be individually assigned to the

Slave transmitter as necessary. It is not necessary to have

model programming in the slave transmitter.

Dx8 Wireless Trainer Operation

1. Enter an unused model on the slave transmitter (computer

transmitter only).

2. Bind the master transmitter to the model.
3. Make sure the master and slave transmitter battery packs are

fully charged.

4. Make sure the slave transmitter is powered off.
5. Either in the Wireless Programmable Master setup page or the

Wireless Pilot Link Master setup page, select BIND. This will

put the master transmitter’s wireless trainer receiver into bind

mode. You should see the following screen:

6. Enter bind mode on the slave transmitter following the

instructions provided with that transmitter.

7. After a successful bind, the following screen should appear:

8. Press the trainer button on the master transmitter to transfer

model control from the master to the slave.

9. Release the trainer button and the master transmitter regains

control of the model.

Master Override

The Master Override feature enables the instructor to immediately

regain control of the model by moving the control sticks. After you

activate Master Override, the slave transmitter cannot control the

model until you reset the trainer switch. To reset the trainer switch:

1. Move the trainer switch to the OFF position.
2. Move the trainer switch to the ON position to activate the slave

transmitter.

SYSTEM SETUP



Wireless Trainer

Summary of Contents for DX8G2






















































Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands

Spectrum DX8G2, Instruction Manual

Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands