Spectrum DX8G2 Instruction Manual Download

Page: 34 / 53

SPEKTRUM DX8G2 • TRANSMITTER INSTRUCTION MANUAL

V-Tail Differential



Only available in Sailplane Type when V-Tail A or V-Tail B is active. See

SAiL

(Sailplane) section for set up.

Camber Preset



Only available in Sailplane Type when a 2+ aileron wing type is selected. See

SAiL

(Sailplane) section for set up.

Camber System



Only available in Sailplane Type when a 2+ aileron wing type is selected. See

SAiL

(Sailplane) section for set up.

Flap System



Only available in Airplane Type when a flap-enabled wing type is selected. See

ACRO

(Airplane) section for set up.

Pitch Curve



Only available in Helicopter Type. See

HELi

(Helicopter) section for set up.

Swashplate



Only available in Helicopter Type. See

HELi

(Helicopter) section for set up.

Gyro



Only available in Helicopter Type. See

HELi

(Helicopter) section for set up.

Tail Curve



Only available in Helicopter Type. See

HELi

(Helicopter) section for set up.

Motor Cut



Only available in Multicopter Type. See

MULTi

(Multicopter) section for set up.

Motor Curve



Only available in Multicopter Type. See

MULTi

(Multicopter) section for set up.

The following menu options are only available when they are enabled from the Model Type screen.

Mixing allows control input for a channel to affect more than one

channel at a time. Mixing functions support:

•  Mixing a channel to another channel.
•  Mixing a channel to itself.
•  Assigning offset to a channel.
•  Linking primary to secondary trim.

These mixes are available for each model memory:

Select a channel for master and slave. Inputs for the

master channel control both the master and slave channels. For

example, Elevator to Flap makes elevator the master channel and

flap the slave channel.

Offset

Change the Offset value to move the effective center position

of the slave channel. Positive or negative value determines the

direction of the offset. Offset is not available for curve mixes.

Trim

If the master channel trim should also adjust the slave channel, set

Trim to Act. A channel monitor on the left side of the screen

shows how channels respond to input. To view a switch-assigned

mix on the monitor, the mix switch must be in the active position.

• 8 programmable mixes

• Cyclic to Throttle (HELI)

• Swashplate (HELI)

• Elevator to Flap (ACRO)

• Aileron to Rudder (ACRO)

• Rudder to Aileron/Elevator (ACRO).

• Aileron>Rudder (SAIL)

• Aileron>Flap (SAIL)

• Elevator>Flap (SAIL)

• Flap>Elevator (SAIL)

if you wish to assign a mix to a switch position:

1. Make sure you are in the desired mix screen.
2. Move the switch you want to assign the mix to.
3. Scroll to the switch position where you want the mix to be

active.

4. Press the scroll wheel to activate the mix. When the box is

filled, the mix is active.

The mix is Active when the box is filled and Inactive when the

box is open. You can assign a mix to be active in multiple switch

positions (0,1 or 2).

Tip:

Use Auto Switch Select to select the switch.

CAUTION:

Always do a Control Test of your model after

changing mixes.

FUNCTION LIST

Mixing

Assigning a Mix to a Switch

Summary of Contents for DX8G2






















































Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands

Spectrum DX8G2, Instruction Manual

Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands