Spectrum DX8G2 Instruction Manual Download

Page: 49 / 53

SPEKTRUM DX8G2 • TRANSMITTER INSTRUCTION MANUAL

Problem

Possible Cause

Solution

Aircraft will not Bind (during

binding) to transmitter

Transmitter too near aircraft during binding

process

Move powered transmitter a few feet from

aircraft, disconnect and reconnect flight

battery to aircraft

Aircraft or transmitter is too close to large metal

object

Move the aircraft or transmitter away from the

large metal object

The bind plug is not installed correctly in the

bind port

Install bind plug in bind port and bind the

aircraft to the transmitter

Flight battery/Transmitter battery charge is

too low

Replace/recharge batteries

Transmitter is a DX8 EU version and receiver is

DSM2

The DX8 EU version is not compatible with

DSM2 receivers

Aircraft will not link (after

binding) to transmitter

Transmitter too near aircraft during linking

process

Move powered transmitter a few feet from

aircraft, disconnect and reconnect flight

battery to aircraft

Aircraft or transmitter is too close to large metal

object

Move the aircraft or transmitter away from the

large metal object

Bind plug left installed in bind port

Rebind transmitter to the aircraft and remove

the bind plug before cycling power

Aircraft bound to different model memory

(ModelMatch™ radios only)

Select correct model memory on transmitter

Flight battery/Transmitter battery charge is

too low

Replace/recharge batteries

Transmitter may have been bound using different

DSM protocol

Bind aircraft to transmitter

Damaged remote receiver or receiver extension.

Required remote receiver is not connected

The receiver goes into failsafe

mode a short distance away from

the transmitter

Check the receiver antenna to be sure it is not

cut or damaged

Replace or contact Horizon Product Support

Main and remote receivers too near each other

Install main and remote receivers at least 2

inches (51mm) apart

Receiver quits

responding during operation

Low battery voltage

Completely recharge flight battery

Loose or damaged wires or connectors between

battery and receiver

Do a check of the wires and connection

between battery and receiver. Repair or

replace wires and/or connectors

Receiver loses its bind

Bind button pressed before transmitter powered on

Rebind by performing binding instructions

Receiver slowly blinking at

landing (DSM2 Only)

Loss of power to the receiver during flight

Check battery voltage

System powered on and connected, then

receiver powered off without powering off

transmitter

Power off transmitter when receiver is

powered off

Flight log registers undesirable

number of fades, losses or holds

or aircraft responds irregularly to

controls

Poor signal reception

Reposition remote receivers for improved RF

signal path diversity

Electronic feedback

Check for and stop feedback from servos or

motor systems to the ESC or receiver

Low power

Check aircraft power draw and increase

battery power or decrease power demand by

installed systems. Ensure all aircraft batteries

are fully charged. Ensure the installed BEC for

an electric aircraft is adequate for the power

demand

TROUBLESHOOTING GUIDE

Summary of Contents for DX8G2






















































Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands

Spectrum DX8G2, Instruction Manual

Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands