background image

GENERAL SAFETY

EVER

NEVER

 allow children to operate this log splitter.

 NEVER 

allow adults lacking proper instructions and understanding to

operate this log splitter.

KEEP

 all people and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the

operator is to be near the log splitter during use.

NEVER

 actuate the control until all people are clear of the work area.

NEVER 

operate the log splitter when under the influence of alcohol, drugs or medication.

NEVER

 allow a person who is tired or otherwise not alert to operate the log splitter.

PREPARATION OF THE LOG

Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 26 in. in length.

WORK AREA

NEVER

 operate the log splitter on slippery, wet, muddy or icy ground.

ONLY

 operate your log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall

off.

NEVER 

operate your log splitter in an enclosed area. Exhaust fumes contain carbon monoxide which can be deadly when

inhaled.

NEVER 

attempt to move your log splitter over hilly or uneven terrain without a tow vehicle or adequate help.

ALWAYS

 block the wheels to prevent movement of the log splitter while in operation.

ONLY

 operate your log splitter in daylight or under good artificial light.

ALWAYS

 keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble

over it.

OPERATION OF THE LOG SPLITTER

Failure to follow these instructions may result in serious injury or death.

OPERATOR
ZONE

TONGUE

FOOT PLATE

ENGINE

BEAM

ONLY 

operate the log splitter from the operator zone as

shown in the diagram. The operator has the safest and
most effcient access to the control valve and the beam
in this location.Failure to operate the log splitter in this
position can result in serious injury or death.

Page 3

ALWAYS

E

read the operator’s manual before operation. It is located in the plastic canister on the tongue.

Summary of Contents for 52020000




















Reviews: