background image

10

Trouble Shooting

You may save time and money by checking items below before calling for service. List includes common concerns that

are not the result of defective workmanship or materials. If your question is not explained below, contact Speed Queen

® Consumer Affairs Department at 

800-843-0304.

723,&

3266,%/(&$86(

62/87,21

NOISE

Gear sounds or a low hum

Normal mechanical sounds in commercial-
quality washer

Normal operation.

Loose objects, such as coins or pins, in tub
or pump

Stop washer and check tub. Remove loose objects. If noise
continues after washer is restarted, objects may be in
pump: call your authorized servicer.

Rattling and clanking noise

Belt buckles, metal fasteners hitting wash tub

Close zippers, buttons, and fasteners. Clothing with
buckles must be turned inside out.

Squealing sound or hot
rubber odor

Overloaded wash tub

Do not overload washer. Stop washer and reduce size of
load.

Thumping sound

Heavy wash loads; unbalanced loads

Usually normal, but unbalanced loads should be
redistributed. Stop washer and rearrange load.

Vibrating noise

Washer not resting firmly on floor

Make sure floor is strong enough for washer. Adjust
leveling legs so washer rests firmly on floor. See

Installation Instructions

 for leveling details.

Wash load distributed unevenly in tub

Stop washer and rearrange load.

Shipping plug not removed during installation

See 

Installation Instructions

 for details on removing

shipping plug.

Water splashing or slapping
noise

Spray rinse

Normal operation. Washer sprays water inside tub while
running at high speed during rinse and spin.

Whistling or whirling noise

Drum spinning without cloths

Normal operation. Holes in the tub can cause this sound.

OPERATION

Washer does not start

Electrical power cord may not be plugged in,
or connection may be loose

Make sure plug from power cord fits tightly into wall outlet.

Fuse blown, circuit breaker tripped, or power
outage occurred

Replace fuse or reset circuit breaker. Do NOT increase
fuse capacity. Call qualified electrician to correct circuit
overload problem. Call local utility company to correct
power outage.

Water supply faucets not turned on

Turn on water supply faucets.

Timer knob/cycle selector set incorrectly

Move indicator slightly clockwise. Pull out on timer knob.

Motor overheated

Internal overload protector automatically stops motor in
event of overload. Protector resets in approximately 3
minutes and motor automatically restarts. If overload
protector stops motor again, quit using washer and call
service technician.

Do not overload washer. Largest dry load level should not
be higher than bottom of fabric softener dispenser or top of
agitator.

Washer won’t spin

Lid partially open

Close lid completely.

Residue left in tub

Heavily soiled items

Wipe tub with non-abrasive household cleaner and rinse.
Before washing, shake or brush excess dirt and sand from
items.

Summary of Contents for Top loading Washer













Reviews: