background image

E

N
G

L

I

S

H

E
S
P

A
Ñ
O

L

F

R

A
N

Ç

A

I

S

Operating Instructions 

Cast Iron Series

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. 
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or 
property damage! Retain instructions for future reference.

Form 5S6024

Safety Guidelines

This manual contains information that is 
very important to know and understand. 
This information is provided for SAFETY 
and to PREVENT EQUIPMENT PROBLEMS. 
To help recognize this information, 
observe the following symbols. 

 

Danger indicates an  

  imminently 

hazardous situation which, if not 
avoided, WILL result in death or serious 
injury.
 

Warning indicates a  

  potentially 

hazardous situation which, if not 
avoided, COULD result in death or 
serious injury.
 

Caution indicates a  

  potentially 

hazardous situation which, if not 
avoided, MAY result in minor or 
moderate injury.
 

Notice indicates  

  important 

information, that if not followed, may 
cause damage to equipment.

NOTE:

 Information that requires special 

attention.

Breathable Air Warning

This compressor/pump is NOT 
equipped and should NOT be 
used “as is” to supply breathing 
quality air. For any application of 
air for human consumption, you 
must fit the air compressor/pump 
with suitable in-line safety and 
alarm equipment. This additional 
equipment is necessary to properly 
filter and purify the air to meet 
minimal specifications for Grade 
D breathing  as described in 
Compressed Gas Association 
Commodity Specification G 7.1 
- 1966, OSHA 29 CFR 1910. 134, 
and/or Canadian Standards 
Associations (CSA).

DISCLAIMER OF WARRANTIES
IN THE EvENT THE COMPRESSOR 
IS uSED FOR THE PuRPOSE OF 
bREATHING AIR APPLICATION 
AND PROPER IN-LINE SAFETy 
AND ALARM EquIPMENT IS 
NOT SIMuLTANEOuSLy uSED, 
ExISTING WARRANTIES ARE vOID, 
AND DAyTON ELECTRIC MFG. 
CO. DISCLAIMS ANy LIAbILITy 
WHATSOEvER FOR ANy LOSS, 
PERSONAL INjuRy OR DAMAGE.

unpacking

After unpacking the unit, inspect 
carefully for any damage that may 
have occurred during transit. Make sure 
to tighten fittings, bolts, etc., before 
putting unit into service.

 

Do not operate tool  

  if damaged during 

shipping, handling or use. Damage 
could result in bursting and cause 
injury or property damage.

General Safety Information

CALIFORNIA PROPOSITION 65

 

This product or its  

  power cord may 

contain chemicals known to the State 
of California to cause cancer and birth 
defects or other reproductive harm. 
Wash hands after handling.
 

You can  

  create 

dust when you cut, sand, drill 
or grind materials such as 
wood, paint, metal, concrete, 
cement, or other masonry. This dust 
often contains chemicals known to 
cause cancer, birth defects, or other 
reproductive harm. Wear protective 
gear.

IN613800AV 6/08

Printed in U.S.A.
02433
0608/176/VCPVP

Description

Air compressor units are intended to provide compressed air to power pneumatic 
tools and operate spray guns. The pumps supplied are oil lubricated. A small amount 
of oil carryover is present in the compressed air stream. Applications requiring air 
free of oil or water should have the appropriate filter installed. The air compressor 
unit must be mounted on a solid floor or solid ground. Any other use of these units 
will void the warranty and the manufacturer will not be responsible for problems or 
damages resulting from such misuse.

Speedaire

®

 Stationary 

Air Compressors

For Warranty & Service call 1-888-606-5587
Do Not Return To Branch

Summary of Contents for 4ME96

























Reviews: