Spektrum NX6 Instruction Manual Download

Page: 11 / 53

SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL

AR6610T TELEMETRY RECEIVER

(Not included with SPMR6775 transmitter only)

The Spektrum

™

AR6610T receiver is a full range telemetry receiver featuring

DSM

technology. It is compatible with all Spektrum

™

aircraft radios that

support DSM2

and DSMX

technology.

Perform the failsafe setup for the AR6610T receiver through a compatible

Spektrum Transmitter with Forward Programming. The Spektrum PC

Programmer can be used for firmware updates.

SPECIFICATIONS

AR6610T

Type

DSM2/DSMX 6 CH Telemetry Receiver

Application

Air

Channels

Receivers

Remote Receiver

(not included)

SRXL2

™

Remote Receiver Optional

[SPM9747]

Modulation

DSM2/DSMX

Data Flight Log

Compatible

Telemetry

Integrated

Bind Method

Bind Button

Failsafe

Yes

Band

2.4GHz

Dimensions (LxWxH)

49.80 x 23.34 x 15.02mm

Weight

12g

Input Voltage

3.5–9V

Resolution

2048

Antenna Length

155mm and 186mm

Bind Button

Bind/Program Port

CH 1/ Smart Port

XBUS Port

SRXL2 Port

Voltage Sensor Port
CH 2
CH 3
CH 4

CH 5
CH 6

Binding

The AR6610T receiver must be bound to your transmitter before

it will operate. Binding is the process of teaching the receiver the

specific code of the transmitter so it will only connect to that spe-

cific transmitter. When new out of the package, the AR6610T will

automatically go into bind mode the first time it is powered on.

Connect the optional SRXL2 remote receiver (SPM9747) if desired and

any telemetry sensors to the main receiver.

Push and hold the bind button on the receiver while turning the receiver

on. Release the bind button once the orange LED starts to flash

continuously, indicating that the receiver is in bind mode.

TIP:

It is still possible to use a bind plug in the BIND port if desired. This

can come in handy if the receiver needs to be mounted in a location that

is difficult to access, in which case a servo extension may be used for

binding. If using a bind plug, remove after binding to prevent the system

from entering bind mode the next time the power is turned on.

Put your transmitter in bind mode.

The bind process is complete when the orange LED on the receiver is

solid.

Failsafe

In the unlikely event that the radio link is lost during use, the

receiver will enable the selected failsafe mode. Smart Safe + Hold

Last is the default setting on the AR6610T. Preset Failsafe and

SAFE Failsafe are only available through forward programming.

Sma Hold Last

If loss of signal occurs, SmartSafe™ technology moves the throttle channel

to its preset failsafe position (low throttle) that was set during binding. All

other channels will hold their last position. When the receiver detects the

signal from the transmitter, normal aircraft operation resumes.

Forward Programming

In your transmitter menu select

Forward Programming

Settings

• Select

Failsafe

-> Select each channel and assign it to Preset or Hold Last.

When you select a different channel for Output, a new group of settings

appears.

Capture Failsafe Postions

Hold the control sticks in the desired failsafe positions and select

Apply

Channel selections must be individually set in Forward Programming to

apply the preset positions or each channel will default to Hold Last. The

value captured will be reflected in the position shown for each channel.

• Initiate Receiver Bind Mode

Gives you the option of putting the receiver into Bind Mode from this

menu.

Preset Failsafe

With preset failsafe, you can set the specific control surface positions you

want to use if the signal is lost. When the receiver detects the signal from

the transmitter, normal aircraft operation resumes.

Only available through Forward Programming

Testing Failsafe

Secure the aircraft on the ground and remove the propeller. Test

Failsafe settings by turning the transmitter RF output off and noting

how the receiver drives the control surfaces.

Receiver Power Only

• If the receiver is turned when no transmitter signal is present, the

throttle channel will not have a control signal to avoid operating or

arming the electronic speed control.

• All other channels have no output until the receiver has linked to the

transmitter.

Summary of Contents for NX6






















































Search results

Summary of Contents for NX6

Reviews:

Related manuals for NX6

Brands by name

Popular brands

Spektrum NX6, Instruction Manual

Search results

Summary of Contents for NX6

Reviews:

Related manuals for NX6

Brands by name

Popular brands