Spektrum NX8 Instruction Manual Download

Page: 3 / 54

SPEKTRUM NX8 • TRANSMITTER INSTRUCTION MANUAL

• NX8 Transmitter (SPMR8200)
• Manual

BEFORE USING YOUR TRANSMITTER

Before going any further, visit the Spektrum Community website at spektrumrc.com to register your transmitter and

download the latest Spektrum AirWare™ firmware updates. A registration reminder screen occasionally appears until

you register your transmitter. When you register your transmitter, the reminder screen does not appear again.

BOX CONTENTS

Support Videos:

For helpful videos on programming the NX8 and other Spektrum

AirWare™ equipped transmitters, go to www.spektrumrc.com/

BATTERY AND CHARGING PRECAUTIONS AND WARNINGS

SPECIFICATIONS

NX8 TRANSMITTER

Type

DSM2/DSMX 8 CH Telemetry Transmitter

Application

Airplanes, Helicopters, Sailplanes, Multirotors

Channels

Wireless Trainer

DSM2*/DSMX Compatible

Switches

2 - 2 Position, 6 - 3 Position,

1 Momentary Button, 2 - Trimmers

Modulation

DSM2*/DSMX

Telemetry

Integrated

Bind Method

Bind Button or From Within Menu

Frame Rate

22ms Default,

11ms Selectable (Digital Servos Required)

Resolution

2048

Battery

3.7V 2,000 mAh LiIon

Band

2.4GHz

Feedback

Tone, Vibration, Voice

*EU versions of the NX8 are not compatible with DSM2

receivers.

WARNING:

Failure to exercise caution while using this

product and comply with the following warnings could

result in product malfunction, electrical issues, excessive heat,

FIRE, and ultimately injury and property damage.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Never attempt to charge dead, damaged or wet battery packs.

• Never attempt to charge a battery pack containing different

types of batteries.

• Never allow children under 14 years of age to charge battery packs.

• Never charge batteries in extremely hot or cold places or place

in direct sunlight.

• Never charge a battery if the cable has been pinched or shorted.

• Never connect the charger if the power cable has been pinched

or shorted.

• Never attempt to dismantle the charger or use a damaged charger.

• Always use only rechargeable batteries designed for use with

this type of charger.

• Always inspect the battery before charging.

• Always keep the battery away from any material that could be

affected by heat.

• Always monitor the charging area and have a fire extinguisher

available at all times.

• Always end the charging process if the battery becomes hot to the

touch or starts to change form (swell) during the charge process.

• Always connect the positive leads (+) and negative leads (–) correctly.

• Always disconnect the battery after charging, and let the

charger cool between charges.

• Always charge in a well-ventilated area.

• Always terminate all processes and contact Horizon Hobby if

the product malfunctions.

• Charge only rechargeable batteries. Charging non-rechargeable

batteries may cause the batteries to burst, resulting in injury to

persons and/or damage to property.

• The USB outlet shall be installed near the equipment and shall

be easily accessible.

CAUTION:

Always ensure the battery you are charging

meets the specifications of this charger. Not doing so can

result in excessive heat and other related product malfunctions,

which can lead to user injury or property damage.

CAUTION:

If at any time during the charging process the

battery pack becomes hot or begins to puff, disconnect

the battery immediately and discontinue the charge process as

batteries can cause fire, collateral damage and injuries.

Summary of Contents for NX8























































Search results

Summary of Contents for NX8

Reviews:

Related manuals for NX8

Brands by name

Popular brands

Spektrum NX8, Instruction Manual

Search results

Summary of Contents for NX8

Reviews:

Related manuals for NX8

Brands by name

Popular brands