background image

12

13

SPEL Stormwater Installation & Operation Manual  |  

SPEL Filter

General Cleaning

Vacuum out of Filter tank, removal, and disposal of 
pollutants at the completion of a standard inspection, 
general cleaning may be deemed necessary 
immediately or scheduled for a future date. Steps 
undertaken for general cleaning should be in general 
accordance with the procedure outlined below but not 
limited.

 

1. Implement Pre-start safety measures.

Ensure that the area in which operational works are to 
be carried out is cordoned off, to prevent unauthorised 
access. Adequate safety barriers must be erected. 
Area in which work is to be carried out must be clean, 
safe and hazard free. (Refer to figure 4.)

 

2. Set-up Gantry Tri-pod above Manhole.

Assemble and position the gantry above the manhole 
safely and as practically as possible. Attach the winch 
or chain block to the gantry for lifting the SPEL Filters. 
Perform safety procedures ie. Attach harnesses etc. (if 
confined space).

 

3. Open manhole lid.

Once you have sent up the Gantry and ensured that 
the area is safe to operate in, you can proceed to open 
the manhole lid, using lid lifters.

 

4. Conduct Gas tests.

(If tank is classed confined space)

Once the lids have been removed to a safe distance to 
prevent tripping, you must then proceed to conduct

gas tests. Perform necessary gas tests according to 
the confined space regulations.

5.  Once confined space has been deemed safe to 

operate in, enter tank safely.

Once you have carried out the required gas test and 
the work area is deemed safe, you may then enter the 
pit via a ladder or winch system to assess the work 
area you will be operating in. Ensure all confined space

 

6. SPELFilter system assessment.

Perform a review of the SPELFilter system using the 
SPELFilter assessment report/checklist.

 

7.  Pollutant removal from tank.

Perform clean-up using a licenced vacuum truck 
contractor or wet/dry vacuum, depending on level of 
sediment built up and/or tank size.

 

8. Reinstate SPELFilter system and disposal.

At the completion of the site inspection, ensure the site 
is reinstated back to its initial state and all pollutants 
are removed from the site in line with pollutant 
disposal procedures.

 

9.  Sign off and forward a copy of the report to 

property manager and SPEL representative.

Summary of Contents for Spel Filter


















Reviews: