SPEX CertiPrep 8000D MIXER/MILL Operating Manual Download

Page: 4 / 21

8000D Mixer/Mill

Page 4 of 21 SPEX CertiPrep 8.21.03

SN and Higher

2. SPECIFICATIONS

Type of mill: High-Energy shaker mill

Grinding container: Canister with balls

Weight (empty, without vial): 68 lbs. (31 Kg)

Dimensions: 22 in (56 cm) x 15 1/4 in (39 cm) x 11 in (28 cm)

Grinding Vials Available (see pages 16-19):

8001 Hardened Steel Vial Set.

8003 Alumina Ceramic Vial Set

8004 Tungsten Carbide Vial Set

8005 Zirconia Ceramic Vial Set

8006 Methacrylate Vial Set

8007 Stainless Steel Vial Set

8008 Silicon Nitride Vial Set

8009 Round-Ended Hardened Steel Vial Set

8014 Agate Vial Set

Smaller Vials also available:

3114 Stainless Steel Vial Set

3117 Hardened Tool Steel Vial Set

3127 Hardened Tool Steel Vial Set

3118 Agate Vial Set

5004 Tungsten Carbide-Lined Vial Set

NOTE: Smaller vials are to be run in Multiple-Sample Adapters (see page 13 & 14)

Electrical: available in 115V 60Hz (8 amp fuse) or 230V 50Hz (5 amp fuse).

Cord: 115V 60HZ version, 3-prong grounded cord supplied.

230V 50HZ version, with European two-prong plug supplied.

NOTE

: Operator is responsible for supplying alternate line cord/plug if required.

Fuses: 115V 60HZ version, 8-amp slow-blow fuse in inlet module,

230V 50HZ version, 5-amp slow-blow fuse in inlet module.

Motor: 1/3 Hp

Clamp Movement: 2¼ in. back-and-forth, 1 in. side-to-side

Clamp Speed: 1060 back-and-forth cycles at 115V/60Hz or 875 at 230V/50Hz

Safety Features: Lid Interlock prevents mill from running if lid is not closed. The latch also

prevents the lid from being opened until the clamps come to a stop.

Controls: start, stop/pause, and stop buttons; programmable timer with digital display, factory-

set for 100 minute range but adjustable to 10, 100, 1000, 10,000 minute ranges.

Summary of Contents for 8000D MIXER/MILL






















Search results

Summary of Contents for 8000D MIXER/MILL

Reviews:

Related manuals for 8000D MIXER/MILL

Brands by name

Popular brands

SPEX CertiPrep 8000D MIXER/MILL, Operating Manual

Search results

Summary of Contents for 8000D MIXER/MILL

Reviews:

Related manuals for 8000D MIXER/MILL

Brands by name

Popular brands