background image

05

SPEX ARM & THIGH SUPPORT USER MANUAL

15

WWW.SPEXSEATING.COM

14.  Both pelvic-belt and shoulder-belt restraints that comply with 

WC18 and/or WC19 should be used to limit occupant movement 

in a crash and reduce the likelihood of occupant ejection from 

the vehicle and/or injurious contact of the occupant with the 

vehicle interior. 

15.  Belt restraints should be positioned on the wheelchair occ-

upant in accordance with WTORS manufacturer’s instructions. 

16. Backrest mounting hardware must be installed correctly. 

Refer to the appropriate section for correct backrest hardware 

mounting instructions.

17.  If the wheelchair is being transported whilst unoccupied, the 

wheelchair must still be secured to the WTORS.

18.  Children whose mass is less than 22kg (48.5 lb) should be 

transferred from their seating system into appropriate child 

restraint systems intended for use in motor vehicles.

19. Sufficient forward and rearward clear space should be 

provided around the wheelchair occupant. Forward clear-space 

zone (FCZ) needs to be larger when a shoulder-belt restraint is 

not used. 

FAILURE TO HEED THESE WARNINGS COULD CAUSE SEVERE INJURY 

TO THE WHEELCHAIR USER OR OTHERS.

Warning

Summary of Contents for Arm & Thigh Supports

















Reviews: