background image

05

SPEX ARM & THIGH SUPPORT USER MANUAL

2

WWW.SPEXSEATING.COM

Introduction

Medifab recommends that a clinician such as an Occupational or Physio Therapist
that is skilled in wheelchair seating and positioning be consulted to determine if
the Spex Arm & Thigh Support is appropriate for the user. The intended user of the Arm 
& Thigh Support is a user with postural support requirements.

Safety Instructions

To avoid injury, read, understand and follow all instructions and warnings in this
manual before installing and using the Spex Arm/Thigh Support. There are hazards asso-
ciated with the use of wheelchairs and adaptive equipment. If you misuse your wheel-
chair or your Arm & Thigh Support you can be seriously injured. If your Arm & Thigh Sup-
port ceases to function as intended, please consult your authorised Spex seating supplier 
immediately before continuing to use. 

The Arm & Thigh support foam meets the flammability requirements of California 
Technical Bulletin 117. The Arm support fabric meets the flammability requirements of 
California Technical Bulletin 117. The Thigh support fabric meets the flammability require-
ments of AS/NZS 3744:1. In rare cases the Neoprene fabric may cause a skin irritation for 
people with sensitve skin. If you experience any reddening or itching of the skin consult 
with your health care professional.

Disclaimer: 

Medifab takes no responsibility as to the therapeutic effectiveness of our 

products. Our claims relate to the ability of the products to provide safe and reliable 
positioning and seating on the equipment onto which they are installed.

Compatibility

• 

Spex Arm & Thigh Support has been designed to be compatible with most wheel-
chairs. 

• 

Spex Arm & Thigh supports are designed to be installed to the Spex Grid-Base seat 
pan or to the seat rail channels.

• 

Spex Arm & Thigh supports can be installed to other wheelchair seat pans / seat 
rails ensuring that a strong and rigid mounting surface is present to enable effective 
installation and on-going use.

• 

Spex Arm & Thigh supports are tested and certified for the Spex brand and may not 
be appropriate for installation to other brands of wheelchairs. 

• 

Spex Arm & Thigh supports are not to be used in a different manner other than 
what they have been designed for. 

Disposal & Recycling

Your Spex Seating System is manufactured using a variety of materials, of which most 
can be recycled. Once it reaches the end of its life, if you are the legal owner, do not 
dispose of as ordinary household waste but take your Spex system to an approved recy-
cling or collection point, to dispose of according to local laws and regulations. 
Separate collection and recycling of the Spex System when disposing ensures protection 
of the environment and assists with natural resource conservation. 

Summary of Contents for Arm & Thigh Supports

















Reviews: