background image

Page 2 of 3 

WARRANTY LIMITATIONS 

6.1 

The  Supplier  makes  no  warranties  or  representations  other  than  those  set  out  in  this  warranty  document  except  as  is 
required by law.  

6.2 

The Supplier will not be liable under this warranty:-  

(i) 

to  the  Client  or  any  other  person  for  any  consequential,  direct  or  indirect  loss,  damage  or  costs  incurred  or 
suffered by the Client or any other person, including but not limited to damage to persons, other property, loss of 
turnover, loss of profits, loss of business or goodwill;  

(ii) 

to the Client for transportation or travel costs which are the Client's responsibility; 

(iii) 

for damage or defects in any Goods caused by improper transportation, storage or any other misuse, neglect or 
accident.  

(iv) 

for  the  installation  of  the  Goods.  Any  fault  or  defect  due  to  installation  should  be  referred  to  the  installer.  The 
Goods must be installed in accordance with the Manufacturer’s instructions and any relevant legislation or code. 

6.3 

This warranty covers the Client only and it is not transferrable if the Goods are sold by the Client during the warranty 
period. 

WARRANTY EXCLUSIONS 

7.1 

This warranty will not apply where:  

(i) 

the Goods have been improperly modified or repaired or the Good's defect has arisen due to the Client's failure to 
properly  install,  fit,  maintain,  service  or  use  the  Goods  in  accordance  with  the  specifications  and  instructions 
provided  by  the  Manufacturer,  including  a  failure  to  comply  with  the  relevant  maintenance  schedule  (where 
applicable); 

(ii) 

the Supplier cannot establish any Defect in the Goods after testing;  

(iii) 

the Goods have been used other than for the purpose for which they were designed;  

(iv) 

the Goods have been subject to abnormal conditions, including but not limited to temperature, pressure, stress, 
load or similar;  

(v) 

the  Client  or  installer  have  used  or  fitted  non-genuine  or  non-approved  parts  and  accessories  to  the  Goods  or 
have failed to use recommended parts and accessories;  

(vi) 

the Good's defect has arisen due to abuse, misuse, neglect or accident; 

(vii) 

the Goods have not been installed in accordance with the relevant instructions;  

(viii) 

the Go

od’s defect is caused by use or fair wear and tear of the Goods (or expendable parts). 

RIGHTS AT LAW 

8.1 

The  benefits  given  to  the  Client  under  this  warranty  are  in addition  to  other  rights  and  remedies  of  the  Client at  law  in 
relation to the Goods.  

8.2 

In  Australia  our  Goods  come  with  guarantees  that  cannot  be  excluded  under  the  Australian  Consumer  Law.    You  are 
entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or 
damage. You are also entitled to have the Goods repaired or replaced if the Goods fail to be of acceptable quality and 
the failure does not amount to a major failure.  

 

Summary of Contents for TCR-001









Reviews: