background image

           - 14 -

IMPORTANT

When fitting a plug to the mains lead it is essential that it contains an
earthing/grounding contact and that this is connected. Under no circumstances
should this equipment be connected to a mains supply which does not include an
earthing/grounding wire and contacts. e.g.. 2 –Wire extension leads as used for
some domestic equipment 

MUST NOT BE USED.

NOTE:-

  The cable colour coding used for the Control Unit and its supplied mains cable is as

follows:-

Pole

US/JAPAN

U.K.

Live

L

Black

Brown

Neutral

N

White

Blue

Earth / Ground

E

Green

Green/Yellow

For U.K. Equipment:

The wire which is coloured 

GREEN and YELLOW

 must be connected to the terminal in the

plug which is marked with the letter 

E

 or by the earth symbol, or coloured green or green and

yellow.  The wire which is coloured 

BLUE

 must be connected to the terminal which is marked

with the letter 

or coloured black.  The wire which is coloured 

BROWN

 must be connected to

the terminal which is marked with the letter 

L

 or coloured red.

NOTE:-

The terminals used in the mains connector on the control panel of the unit are:-

POLE

PIN No.

Live

Pin 1

Neutral

Pin 3

Earth / Ground

Pin E

The method of disconnection from the mains electrical supply is by removal of the mains lead
plug from its respective supply socket.

OPERATING PRINCIPLE

The SAS control power supply transforms the 110/220 Vac into an adjustable voltage 
which can be set from 3.5 to 13 Vdc.

The generator at the spray head converts the 12 Vdc into 85 kV negative charge, the 
material being applied is drawn to the positively grounded product.

Summary of Contents for SAS D/C























Reviews: