spikenzielabs The Rainbow Light Show Instruction Manual Download | Manualshive

Page: 4 / 15

background image

Flare out the legs to keep them in place. Be sure that the body of the resistor is flush against the PCB.

Solder the resistors in place. Make sure you don’t
forget to solder any of the legs.

Snip off the ends of the legs. Be sure not
to scratch the surface of the PCB. Keep
your safety glasses on!

Do this for each resistor leg.

!

Safety Glasses On!

Capacitor preparation and soldering

Place the capacitors in the two locations
as seen in these photos. Marked as 0.1uf
on the PCB.

Orientation does not matter for these.

Flare the legs out as your did for
the resistors, and then solder both
capacitors in place.

Snip the ends of the legs.

«
...
2
3
4
5
6
...
»

Summary of Contents for The Rainbow Light Show
















Reviews:

No comments

Related manuals for The Rainbow Light Show

Brand: taiyo Pages: 4

Brand: taiyo Pages: 32

Brand: Hakko Electronics Pages: 2

Brand: Oki Pages: 6

Brand: jbc Pages: 12

Brand: Surtek Pages: 4

Brand: Surtek Pages: 12

Brand: X-Tronic Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands