background image

B. Injector removal/replacement.

1. Remove the pan support by pulling up to release it from the plastic clips.
2. Remove the appropriate burner cap and skirt.
3. With a 7mm A/F socket, unscrew the injector from the bottom of the burner mixing

tube.

4. Replace/refit using the reverse procedure.

C. Thermocouple removal/replacement.

1. Shut off gas supply and disconnect gas supply pipe from the unit.
2. Remove the hob from the bench top.
3. Unscrew the appropriate thermocouple nut next to the burner.
4. From the underside of the hob, unscrew the appropriate thermocouple nut at the

gas valve.

5. Remove the thermocouple.
6. Replace/refit using reverse procedure.

D. Gas valve removal/replacement.

1. Shut off gas supply and disconnect gas supply pipe from the unit.
2. Remove the hob from the bench top.
3. From the underside of the hob, unscrew the appropriate gas supply nut at the

mixing tube.

4. From above the hob, unscrew the two screws retaining the mixing tube to the hob.
5. Remove the mixing tube.
6. Replace/refit using reverse procedure.

E. Grill burner removal/replacement.

1. Shut off gas supply and disconnect gas supply pipe from the unit.
2. Remove the hob from the bench top.
3. Unscrew the two screws retaining the grill burner to the hob.
4. From the underside of the hob, unscrew the thermocouple nut at the grill burner.
5. Lift the grill burner clear of the thermocouple and injector.
6. Replace/refit using reverse procedure.

F. Grill burner removal/replacement.

1. Follow procedure E1 to E5.
2. With a 7mm A/F socket, unscrew the injector from its holder.
3. Replace/refit using reverse procedure.

BUILD IN

COOKING HOB

FOR USE WITH LIQUID PETROLIUM GAS

MODELS H200F,H250F,H400F &

854F

User and Installation Instructions

PLEASE READ THOROUGHLY and keep for future

reference.

FOR USE IN AUSTRALIA

SPINFLO LIMITED, 4-10 Welland Close, Parkwood Industrial

Estate, Rutland Road, Sheffield S3 9QY, ENGLAND.

TEL: + 44 114 273 8157

FAX: + 44 114 275 3094

P

C

C

1273Z

 – 

Is

su

WARNING

Only use this appliance in a well ventilated area.

Read the instructions before use.

This appliance must be installed by an
authorised person.

Summary of Contents for H200F

Page 1: ...g tube to the hob 5 Remove the mixing tube 6 Replace refit using reverse procedure E Grill burner removal replacement 1 Shut off gas supply and disconnect gas supply pipe from the unit 2 Remove the hob from the bench top 3 Unscrew the two screws retaining the grill burner to the hob 4 From the underside of the hob unscrew the thermocouple nut at the grill burner 5 Lift the grill burner clear of th...

Page 2: ... back edges of the cut out as shown on section A A The appliance should be fixed in position using countersunk woodscrews fitted through the pan rest clips as shown For models 854F and H250F the front of the cupboard should be cut out as shown below to fit the grillbox Overall Dimensions 854F 4BF W500mm x D400mm x H152mm 854F 4BFG W500mm x D400mm x H152mm Combination unit W1145mm x D400mm x H152mm...

Page 3: ...mption 8 Series 4 Burner 20 0 M 8 Series 4 Burner Grill 25 0 M Combination 4 Burner Grill Sink 25 0 M 2 Series 2 Burner 10 0 M Midi Hobs 2 Burner Grill 15 0 M FITTING Place the appliance over the worktop cut out and connect to the gas supply as detailed below For models 854 and 250 slide the grill compartment into place and fix it to the sides of the cupboard cut out with 2 screws on each side CON...

Page 4: ... inwards so they cannot be caught accidentally 2 Never leave fat or oil unattended on the hotplate 3 When finished check that all controls are in the off position 4 This appliance must not in any circumstances be used as a space heater 5 If fitted in a touring caravan or motor van all burners should be extinguished when the vehicle in which the appliance is installed is moving It is preferred that...

Reviews: