background image

                                                                                                                                                       

IN839

 

 
 
 

 
 

 

NEVER 

operate this treadmill without reading and completely understanding the 

results of any operational change you request from the computer. 

 

Understand that changes in speed and incline do not occur immediately. Set your 

desired speed on the computer console and release the adjustment key. The 
computer will obey the command gradually. 

 

NEVER 

use your treadmill during an electrical storm. Surges may occur in your 

household power supply that could damage treadmill components. 

 

Use caution while participating in other activities while walking on your treadmill; such 

as watching television, reading, etc. These distractions may cause you to lose 
balance or stray from walking in the center of the belt; which may result in serious 
injury. 

 

NEVER 

mount or dismount the treadmill while the belt is moving. Spirit treadmills 

start at a very low speed and it is unnecessary to straddle the belt during start up. 
Simply standing on the belt during slow acceleration is proper after you have learned 
to operate the unit. 

 

Always hold on to a handrail or hand bar while making control changes (incline, 

speed, etc.). 

Do not use excessive pressure on console control keys. They are precision set to 
function properly with little finger pressure. Pushing harder is not going to make the unit 
go faster or slower. If you feel the buttons are not functioning properly with normal 
pressure, contact your Spirit dealer. 

 
 
 

A safety tether cord is provided with this unit. It is a simple magnetic design that should 
be used at all times. It is for your safety should you fall or move too far back on the 
tread-belt. 
Pulling this safety tether cord will stop tread-belt movement. 
 

To Use: 

1. Place the magnet into position on the round metal portion of the console control head. 
Your treadmill will not start and operate without this. Removing the magnet also 
secures the treadmill from unauthorized use. 
 
2. Fasten the plastic clip onto your clothing securely to assure good holding power. 

Note: 

The magnet has strong enough power to minimize accidental, unexpected 

stopping. The clip should be attached securely to make certain it does not come off. Be 
familiar with its function and limitations. The treadmill will stop, depending on speed, 
with a one to two step coast anytime the magnet is pulled off the console. Use the red 

Important Operation Instructions

 

Safety Tether Cord

 

Summary of Contents for inspire IN839

















Reviews: