6
Elliptical
Trainer
XE
395
1. Slide the Incline Rail Assembly (
2
) into the U channel of the Main Frame (
1
). Be very careful not to damage the
wires that exit each part.
2. Connect the Incline Rail Assembly (
2
) horizontally to the U channel of the Main Frame (
1
) with two Hex
Head Bolts (
77
), two Flat Washers (
96
), and two Nyloc Nuts (
89
). Secure it vertically with four Hex Head
Bolts (
167
), four split washers (
178
), four Flat Washers (
100
), and four star washers (
179
). Tighten using the
wrenches provided (
124
&
129
).
3. Connect the Incline Motor wires (
37
&
38
) to the wiring harness & black wire that exits the Incline Rail
Assembly (
2
). Push the excess cable inside the U channel.
4. Guide the twist tie that is attached to the Computer Cables (
36
&
39
) bundle through the Console Mast
Cover (
49
) and the bottom of the Console Mast (
12
) until it exits the top of the steel tube
Note: make sure the
console mast cover is positioned like the illustration.
Secure the Console Mast (
12
) by loosely threading two Hex
Head Bolts (
76
) from the front and two Curved Washers (
104
) first. Then secure the mast from the side by
loosely threading a Hex Head Bolt (
75
) and a Split Washer (
128
);
Note: there is one bolt already installed in the
receiving bracket that will engage with the slot at the bottom of the Console Mast. Tighten the bolt from the left side
last.
5. Tighten the two front bolts first, then the side bolts with the wrench (
124
). Secure the Console Mast Cover
(
49
) over the top of the plastic side covers (
50
&
51
).
6. Untie the twist tie, which is attached to the Computer Cables (
36
&
39
). Plug in the connectors of the two
Hand pulse cables (
44
), Computer cable (
36
&
39
), Resistance cable (
146
), and Incline cable (
146-1
) in the
bottom of the Console (
32
). Secure the Console (
32
) onto the mounting plate with four Phillips Head Screws
(
85
). Tighten them with the Phillips Head Screw Driver (
126
).
HARDWARE
STEP 1:
Incline Rail & Console Mast
#96.
3/8” x 19 x 1.5T
Flat Washer
(2 pcs)
#100.
5/16” x 20 x 1.5T
Flat Washer
(4 pcs)
#104.
3/8” x 23 x 1.5T
Curved Washer
(2 pcs)
#128.
3/8” x 2T
Split Washer
(1 pc)
#85.
M5 x 10mm
Phillips Head Screw
(4 pcs)
#89.
3/8” x 7T
Nyloc Nut
(2 pcs)
#178.
5/16” x 1.5T
Split Washer
(4 pcs)
#179.
5/16”
Star Washer
(4 pcs)
#76.
3/8” x 3/4”
Hex Head Bolt
(2 pcs)
#77.
3/8” x 1-1/2”
Hex Head Bolt
(2 pcs)
#167.
5/16” x 2-1/4”
Hex Head Bolt
(4 pcs)
#75.
3/8” x 2-1/4”
Hex Head Bolt
(1 pc)
Summary of Contents for XE395 Elliptical
Page 2: ......
Page 4: ...2 Elliptical Trainer XE395 ...
Page 11: ...7 Elliptical Trainer XE395 ...
Page 15: ...11 Elliptical Trainer XE395 ...
