7
www.nuui.pl
www.spokey.pl
MAINTENANCE
Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.
Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.
The device should be kept in a dry place in order to protect it against
dampness and corrosion.
Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.
In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
should be made by a qualified SPOKEY’s company employee.
POWER SUPPLY
Batteries: 1.5V AA (2 pieces), not supplied with the bicycle
Inserting batteries
1. Insert two batteries at the back of the counter.
2. Make sure that the batteries are correctly positioned.
3. If the display is unreadable or only some segments are visible, remove
the batteries and re-insert them.
4. After removing the batteries, all function values will
be reset.
COUNTER
First start-up
Before the first start-up, make sure that all the cables have been connected
correctly and that the batteries have been inserted correctly.
The display will turn on once you press the button or when you start
pedaling.
Auto on-off
After 4 minutes, the meter enters the energy saving mode. All settings and
data are kept until restarting the meter.
In case the screen does not start, disconnect power supply and wait for 15
seconds.
Resetting
To reset all values, keep the MODE button pressed for two seconds. Note:
Values will also be reset when the battery is removed from the gauge.
Device error
If an incorrect reading appears on the counter, remove the batteries and
reinsert them.
Button
The gauge is equipped with a universal button for selecting individual
functions (MODE).
Press the MODE button to go to the selected function. Press and hold the
MODE button for 4 seconds to reset
Functions
SCAN: the training effects will be alternately displayed on the monitor: time,
speed, distance, number of calories burned, and heart rate. Each
parameter will be displayed for 6 seconds. Press the MODE button during
the presentation of a given function to stop it on the display (the SCAN
function will be deactivated).
TIME: It shows your exercising duration. It starts from 00:00 to 99:59min
SPEED: It shows your pedaling speed on the machine. It starts from 0.00
to 99.9km/h.
DISTANCE: It shows how many Kilometer or Miles you have worked on the
machine. It starts from 0.00 to 999.9km.
CALORIES : it shows how many calories you have burned. It starts from
0.00 to 999.9kcal. The data shown is generic, given for comparing different
training sessions. They should not be used for medical purposes.
PULSE: Displays the current pulse level during training. To obtain the
correct measurement, it is necessary to put both hands on the sensors built
into the handle bars for min. 5 seconds. The current heart rate value will
appear on the display. If the sensor does not detect a heart rate, the
“P”
symbol will show up on the display. To check if the pulse rate is stable,
keep your hands on the sensors during the entire training session: The data
shown is generic, given for comparing different training sessions. They
should not be used for medical purposes.
THE SCOPE OF MEASUREMENT
TIMER - TIME 0: 00-99:59 MIN: SEC (min: sec)
SPEED - 0.0-999.9 KM / H (km / h)
DISTANCE - 0.0-99,99 KM
CALORIES - 0.0-999.9 KCAL
PULSE - 40-240 BEATS / MIN (strokes / min) (BPM)
Your body position
Sit on the saddle, put your feet in the pedals so that they are
blocked between the pedal base and the protective belt, put
your hands on the handlebar. During exercises, keep your
back straight (see the drawing).
Exercises with the use of stationary bicycle can replace
exercises done with the use of an ordinary bicycle.
Shaping your muscles
To shape your muscles during exercises, you should increase the
resistance substantially. This will bring about the increased muscle tension
and it may mean that you will not be able to train for as long as you want.
If you would also like to exercise your fitness, you should change your
training programme. You should exercise practising the following stages:
warm-up stage, proper training stage and relaxation stage. However, at the
end of your training, you should increase the resistance, so that you can
enhance the workout of your leg muscles. You should also reduce your
speed, so that the pulse remains at the indicated level.
Weight loss
An important factor here is the effort you put into your exercises. The longer
and harder you train, the more calories you will burn. It will be a success to
obtain the same efficiency as for fitness training.
Intensive training, which helps you to lose your weight, should be carried
out more frequently, for at least approx.: 45-50 minutes
HOW TO OPERATE THE BIKE METER
USAGE AND TRAINING
Summary of Contents for 926199
