15
www.spokey.pl
use cross wrench to make them very tight. If the bolts (20) cannot be
threaded to the hole on the right pedal tube (06R) and left tube (06L),
please adjust the crank angle. Fix pedals(L&R)(11) on the pedal tube (L&R)
(6R&6L) using four outer hex bolts washers(32) and nuts (36). Please use
wrench to fix them.
STEP 4:
Connect swing bar (R & L) (4&5) to axle (23) and two sets of bolts (26),
spring washer (24), washers (40) and wave washers (27).Please use allen
wrench to fix them.
Attach lower swing bar (4&5) (L&R) to the upper connecting handle bar (7)
(L&R) using four Carriage Bolt(25),four Curved Washer (17),four Domed
Nuts (18).
Attach the Fixed Handlebar (9) to the Upper Support (10) with two Screws
(31), two Split Washers (32), and two Curved Washers (39); start both
Screws, and then tighten them.Tip: Avoid pinching the wire.
STEP 5:
Put 1pc or 2pcs of 1.5“AAA”size batteries into the computer. Then see the
computer display numbers on LCD or not. Use cross wrench to demount
2pcs of bolts and washers from the computer. Link the sensor wire (14)
from the computer holder to the sensor wire (14) from the computer
together. Slide the computer into the computer's(15) holder. Use cross
wrench to fasten computer with2pcs of demounted bolts and washers. Link
the 2pcs of handpulse wires (15)from the back of the upper support (10) to
the 2pcs of handpulse wires from the computer together.
Levelling, moving the device
Before you start exercising, it is recommended to verify whether the bike is
positioned correctly. Level the equipment with the knobs of the front
stabilizer. To transport the device, raise it carefully on its front wheels
(Figure
– p. 46) and move to another place, holding it on both sides.
Resistance adjustment
The Resistance adjustment function allows to change resistance on the
pedals. High resistance requires larger effort while pedalling, whereas the
low one decreases the effort. Force of resistance is regulated by a knob
placed on the handlebar post. In order to decrease resistance, adjustment
knob should be turned towards the “1“ number whereas so as to increase
resistance, the knob should be turned towards the “8” number.
In order to achieve a satisfying effect, resistance level should be set during
a training.
MAINTENANCE
Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.
Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.
The device should be kept in a dry place in order to protect it against
dampness and corrosion.
Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.
In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
s
hould be made by a qualified SPOKEY’s company employee.
POWER SUPPLY
Batteries: 1.5V AAA (2 pieces), not supplied with the device
Inserting batteries
1. Insert batteries at the back of the counter.
2. Make sure that the batteries are correctly positioned.
3. If the display is unreadable or only some segments are visible, remove
the batteries and re-insert them.
4. After removing the batteries, all function values will be reset.
COUNTER
First start-up
Before the first start-up, make sure that all the cables have been connected
correctly and that the batteries have been inserted correctly.
The display will turn on once you press the button or when you start
pedaling.
Auto on-off
After 4 minutes, the meter enters the energy saving mode. All settings and
data are kept until restarting the meter.
In case the screen does not start, disconnect power supply and wait for 15
seconds.
Device error
If an incorrect reading appears on the counter, remove the batteries and reinsert them.
Buttons
MODE
selecting the counter functions
SET
setting time, distance, calories, and pulse, when the counter is not in
the SCAN mode.
RESET
resetting time, distance, calories, and pulse. To reset the values,
press the button for 3 seconds.
HOW TO OPERATE THE BIKE METER
