background image

Other items

   

                                                                                                                                                       

 

 

           

Model: 

 

   C575R 

            Item:          KPH/MPH switch, total distance, total time and software version display 

Method:         

1. Press <CHANGE DISPLAY” for 3 seconds to get into user reference and setting mode 

A.

 

English and Metric setting 

The display will show “UNIT-MPH” for English setting or “UNIT-KPH” for metric setting. Press INCLINE 
<

> <

> key to switch the setting. After selection, press <ENTER> to confirm. 

B.

 

Program time limit setting 

The display will show ”TIME LIMIT- YES” or    ”TIME LIMIT- NO”, press INCLINE <

> <

> key to 

change it. After selection, press ENTER to confirm. If the selection is YES, the display will show 
“TIME-XX:00” with default value of 30:00, press INCLINE <

> <

> key to adjust; the range of adjustment 

is 5-60 minutes. Afterwards, press ENTER to confirm. 

C.

 

Language setting 

The display shows ”GERMAN”…,” XX    MILE    H>H” or    ” XX      KM      H_H”, press WORKOUT 
LEVEL<

>/<

>to change the setting. Afterwards, press ENTER to confirm. 

D.

 

Total distance display 

                                            The display shows ”DIST-XXXXXXKM” or “DIST-XXXXXXMILE” for total distance display. Press   
                                            <ENTER> to exit. 

E.

 

Total time display 

                                            The display shows ”TIME-XXXXXXHOUR” for total time display. Press <ENTER> to exit. 

F.

 

Control board software version display 

                                            The display shows ”CTL C575-XX” for software version display. Press <ENTER> to exit. 

G.

 

Drive board software version display 

                                            The display shows ”DRV C575_SG_XX” for software version display. Press <ENTER> to exit. 

 

 

 

 

 

 

 

             

 

3-9-1 

Summary of Contents for C575R








































Reviews: